Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068709 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BACK WINDOW OPENING TRIM

a.

Install the back window opening trim.


Hide 2.INSTALL NO. 2 BACK WINDOW GLASS SPACER

B284186
1.719,2.833 1.75,3.01 1.75,3.01 2.281,3.01 true 0.094,0.094 0.469,0.458 0.375,0.365 10 false *a 2.385,2.896 2.656,3.198 0.271,0.302 10 false *1
*1 Ceramic Notch
*a Backside


a.

Apply Primer G to the back window glass where the spacer will be installed.

HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



b.

Install a new spacer to the glass as shown in the illustration.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




Hide 3.INSTALL BACK DOOR GLASS ADHESIVE DAM

B284084
1.979,0.26 2.26,0.604 0.281,0.344 10 false A 1.979,0.698 2.333,1.073 0.354,0.375 10 false A 1.354,1.25 1.688,1.583 0.333,0.333 10 false A 1.365,1.667 1.677,1.969 0.313,0.302 10 false A 2.375,2.427 2.677,2.75 0.302,0.323 10 false a 0.698,3.115 1.01,3.417 0.313,0.302 10 false *1 0.094,0.094 0.438,0.448 0.344,0.354 10 false *a
*1 Primer G
*a Backside


a.

Apply Primer G to the glass where the adhesive dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Standard:
Area Specified Condition
a 10.0 mm (0.394 in.)



b.

Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area) as shown in the illustration.

B284085
0.875,0.708 0.729,0.969 false 4.188,0.708 4.385,0.979 false 0.083,0.083 0.458,0.448 0.375,0.365 10 false *a 0.563,1 0.854,1.344 0.292,0.344 10 false *1 4.458,0.917 4.729,1.208 0.271,0.292 10 false *1 4.885,0.073 5.365,0.396 0.479,0.323 10 false A - A 5.76,1.74 6.427,2.094 0.667,0.354 10 false C - C 1.073,1.188 1.375,1.479 0.302,0.292 10 false C 1.604,1.344 1.927,1.646 0.323,0.302 10 false C 3.896,1.167 4.188,1.448 0.292,0.281 10 false C 5.198,0.365 5.448,0.635 0.25,0.271 10 false a 6.292,1.104 6.635,1.438 0.344,0.333 10 false a 6.365,1.5 6.625,1.813 0.26,0.313 10 false b 3.385,1.375 3.615,1.667 0.229,0.292 10 false C 2.219,0.698 2.583,1.094 0.365,0.396 10 false A 2.219,1.052 2.542,1.417 0.323,0.365 10 false A 2.219,1.542 2.594,1.885 0.375,0.344 10 false B 2.229,1.896 2.635,2.219 0.406,0.323 10 false B
*1 Ceramic Notch - -
*a Backside - -


Standard:
Area Specified Condition
a 3.2 mm (0.126 in.)
b 11.2 mm (0.441 in.)



Hide 4.INSTALL BACK DOOR GLASS

B284185
2.146,2.135 1.729,2.135 true 2.24,1.021 1.74,0.677 false 2.188,2.042 1.688,1.698 true 2.031,0.188 2.333,0.5 0.302,0.313 10 false *a 1.521,0.573 1.823,0.833 0.302,0.26 10 false *1 1.458,1.604 1.802,1.938 0.344,0.333 10 false *1 0.615,4.344 0.99,4.573 0.375,0.229 10 false : *1 1.49,2.031 1.823,2.375 0.333,0.344 10 false *2 2.021,2.313 2.365,2.635 0.344,0.323 10 false *b
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


a.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

B284187
4.531,1.167 4.833,1.167 true 6.042,1.031 6.156,0.698 6.156,0.698 6.292,1.031 true 4.531,2.771 4.833,2.771 true 6.073,2.646 6.073,2.302 6.073,2.302 6.188,2.302 true 2.333,2.271 2.333,2.49 true 0.104,0.115 0.521,0.458 0.417,0.344 10 false *a 1.521,1.198 1.875,1.542 0.354,0.344 10 false A 1.521,1.552 1.844,1.875 0.323,0.323 10 false A 0.323,1.698 0.688,2.031 0.365,0.333 10 false B 0.865,1.885 1.188,2.177 0.323,0.292 10 false B 1.49,2.031 1.802,2.313 0.313,0.281 10 false C 2.698,1.854 2.969,2.156 0.271,0.302 10 false D 3.26,1.667 3.531,1.979 0.271,0.313 10 false D 1.49,2.396 1.719,2.677 0.229,0.281 10 false C 4.885,1.083 5.229,1.396 0.344,0.313 10 false *2 6.281,2.229 6.615,2.552 0.333,0.323 10 false *2 4.885,2.698 5.229,3.063 0.344,0.365 10 false *2 6.083,0.5 6.417,0.833 0.333,0.333 10 false *2 0.563,3.448 1.083,3.76 0.521,0.313 10 false : *1 3.719,0.375 4.271,0.677 0.552,0.302 10 false A - A 5.49,0.375 6.01,0.75 0.521,0.375 10 false B - B 3.719,2.156 4.281,2.469 0.563,0.313 10 false C - C 5.49,2.156 6,2.5 0.51,0.344 10 false D - D 3.906,0.854 4.208,1.125 0.302,0.271 10 false a 3.885,2.865 4.177,3.135 0.292,0.271 10 false a 5.75,1.594 6.083,1.875 0.333,0.281 10 false b 3.948,1.208 4.292,1.458 0.344,0.25 10 false d 6.135,1.583 6.406,1.896 0.271,0.313 10 false c 6.302,3.198 6.646,3.5 0.344,0.302 10 false b 2.26,2.531 2.594,2.885 0.333,0.354 10 false *2 3.979,2.563 4.26,2.854 0.281,0.292 10 false d 5.906,3.135 6.115,3.365 0.208,0.229 10 false d 6.354,1.542 6.583,1.833 0.229,0.292 10 false d
*1 Primer G *2 Adhesive Center Line
*a Backside - -


Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 16.2 mm (0.638 in.)
c 8.0 mm (0.315 in.)
d 7.0 mm (0.276 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B284188
3.219,2.292 3.219,2.594 true 4.958,1.198 5.167,1.51 5.167,1.51 5.219,1.51 true 6.458,1.052 6.135,0.708 6.135,0.708 6.219,1.052 true 4.958,2.792 5.188,3.094 5.188,3.094 5.26,3.094 true 6.25,2.656 6.542,2.385 6.542,2.385 6.604,2.385 true 0.104,0.125 0.479,0.51 0.375,0.385 10 false *a 1.135,3.365 1.479,3.677 0.344,0.313 10 false *1 3.146,2.635 3.531,2.948 0.385,0.313 10 false *2 5.281,1.406 5.698,1.698 0.417,0.292 10 false *2 5.969,0.531 6.281,0.74 0.313,0.208 10 false *2 5.333,2.99 5.698,3.313 0.365,0.323 10 false *2 6.667,2.281 6.99,2.573 0.323,0.292 10 false *2 2.438,1.219 2.667,1.479 0.229,0.26 10 false A 2.448,1.573 2.719,1.875 0.271,0.302 10 false A 1.24,1.74 1.49,1.969 0.25,0.229 10 false B 1.771,1.927 2.125,2.24 0.354,0.313 10 false B 2.458,2.063 2.729,2.344 0.271,0.281 10 false C 3.656,1.948 3.969,2.313 0.313,0.365 10 false D 4.188,1.76 4.469,2.115 0.281,0.354 10 false D 2.458,2.406 2.823,2.698 0.365,0.292 10 false C 4.271,0.104 4.771,0.396 0.5,0.292 10 false A - A 5.615,0.104 6.219,0.51 0.604,0.406 10 false B - B 4.25,2.125 4.76,2.406 0.51,0.281 10 false C - C 5.615,2.125 6.073,2.396 0.458,0.271 10 false D - D 0.479,2.104 0.844,2.479 0.365,0.375 10 false a 0.281,3.302 0.583,3.583 0.302,0.281 10 false a 6.323,1.583 6.594,1.927 0.271,0.344 10 false b 0.917,2.188 1.219,2.51 0.302,0.323 10 false b 0.719,2.875 0.969,3.125 0.25,0.25 10 false b 4.344,0.833 4.604,1.083 0.26,0.25 10 false c 4.354,2.896 4.542,3.073 0.188,0.177 10 false c 6.479,2.958 6.833,3.229 0.354,0.271 10 false d 5.938,1.583 6.188,1.896 0.25,0.313 10 false d
*1 Adhesive *2 Adhesive Center Line
*a Backside - -


Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 14.0 mm (0.551 in.)
d 16.2 mm (0.638 in.)




d.

Install the back door glass to the vehicle body.

i.

Hold the back window glass in place securely with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the outer surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.


iii.

Connect the 2 rear window defogger connectors.


iv.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the glass rim.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 5.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 6.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 7.INSTALL BACK DOOR GLASS CHANNEL LH

HINT:

When installing the back door glass channel LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new back door glass channel.

i.

Using a heat light, heat the vehicle body.


ii.

Using a heat light, heat the channel.

Standard heating temperature:
Item Specified Condition
Channel 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the channel excessively.



iii.

Remove the peeling paper from the face of a new back door glass channel.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iv.
B085274

Install a new back door glass channel.

HINT:

Press the back door glass channel firmly to install it.



v.

Install the 2 clips.



Hide 8.INSTALL BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedures described for the LH side.


Hide 11.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY