Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM1880E _59 Vehicle Exterior _013251 WIPER / WASHER _0068727 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E184734
1.427,0.594 1.75,0.917 1.75,0.917 2.052,0.573 true 1.75,1.125 1.75,0.917 false 1.708,1.177 2.104,1.406 0.396,0.229 10 false *1
*1 MP grease


Apply MP grease to the entire inner surface of the wiper motor grommet.

HINT:

Make sure that grease is applied so that the grooves in the grommet are filled with grease, but not so that the hole of the grommet becomes clogged with grease.



b.
E226548
2.094,0.458 2.729,0.458 true 2.792,0.396 2.99,0.646 0.198,0.25 10 false *1
*1 Position Mark


Install the rear wiper motor grommet with the position mark facing upward as shown in the illustration.


Hide 2.INSTALL REAR WIPER MOTOR ASSEMBLY

B117895

a.

Install the wiper motor with the 3 bolts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


b.

Connect the connector.


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

Operate the rear wiper, and stop the rear wiper motor at the automatic stop position.


b.
E226552
1.458,1.51 1.115,0.76 1.115,0.76 0.521,0.76 true 0.927,2.594 0.927,3.51 false 2.021,3.635 3.052,3.635 true 0.323,0.677 0.875,1.073 0.552,0.396 10 false *1 0.885,2.406 1.417,2.771 0.531,0.365 10 false *2 3.125,3.531 3.375,3.823 0.25,0.292 10 false *3
*1 Wiper Arm Pivot Serrations
*2 Wire Brush
*3 Wiper Pivot Serrations


Clean the wiper pivot serrations with a wire brush.


c.
E227746
1.573,0.99 1.573,0.344 1.573,0.344 1.417,0.344 true 1.208,0.917 1.208,0.729 false 1.208,1.125 1.208,1.24 true 1.219,0.281 1.542,0.5 0.323,0.219 10 false *1 1.125,0.542 1.438,0.813 0.313,0.271 10 false *a 0.292,0.875 0.802,1.198 0.51,0.323 10 false *b 0.583,1.031 0.885,1.333 0.302,0.302 10 false *c 1.125,1.26 1.458,1.521 0.333,0.26 10 false *d
*1 Ceramic Line
*a Upper Limit
*b 10 mm (0.393 in)
*c 15 mm (0.590 in)
*d Lower Limit


Position the blade tip within the range shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
·

Hold down the arm hinge by hand while tightening the nut.

·

Install the arm and blade so that the rear wiper blade is aligned with the ceramic line.




d.

Operate the rear wiper while spraying water or washer fluid on the glass. Ensure that there is no interference between the blade and pillar.


e.
E226556

Close the wiper arm head cap.


Hide 4.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).