Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068709 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 4.REMOVE BACK DOOR GLASS CHANNEL LH

B085274

a.

Remove the 2 screws.


b.

Using a heat light, heat the channel.

Standard heating temperature:
Item Specified Condition
Channel 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the channel excessively.



c.

Using a screwdriver, detach the double-sided tape and back door glass channel LH.

HINT:

Tape the screwdriver tip before use.



Hide 5.REMOVE BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedures described for the LH side.


Hide 6.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Hide 7.REMOVE BACK DOOR GLASS

a.

Disconnect the 2 rear window defogger connectors.


b.
B284184
0.583,2.833 0.583,2.354 0.583,2.354 0.844,2.354 true 1.656,1.354 1.656,1.552 false 0.344,3.573 0.76,3.25 0.76,3.25 0.958,3.25 true 1.708,3.698 1.708,3.458 1.708,3.458 1.813,3.458 true 0.438,3.823 0.698,4.104 0.698,4.104 0.896,4.104 false 2.833,2.833 2.833,2.365 2.833,2.365 2.573,2.365 true 3.073,3.594 2.708,3.219 2.708,3.219 2.531,3.219 true 0.708,3.063 1.135,3.063 false 1.573,1.604 1.969,1.948 0.396,0.344 10 false *1 0.927,2.26 1.271,2.49 0.344,0.229 10 false *2 1,4.052 1.333,4.375 0.333,0.323 10 false *4 1.198,2.969 1.5,3.26 0.302,0.292 10 false *4 1.885,3.365 2.281,3.604 0.396,0.24 10 false *3 1.01,3.188 1.385,3.5 0.375,0.313 10 false *3 2.354,2.26 2.708,2.563 0.354,0.302 10 false *2 2.333,3.156 2.625,3.438 0.292,0.281 10 false *3
*1 Protective Tape
*2 Clip
*3 Spacer
*4 Piano Wire


Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



c.

From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


e.

Cut through the adhesive by pulling the piano wire around the back door glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back door glass.



f.

Using suction cups, remove the back door glass.


Hide 8.REMOVE BACK WINDOW OPENING TRIM

B289598

a.

Remove the back window opening trim.


Hide 9.CLEAN BACK DOOR GLASS

BO04421

a.

Clean the outer edge of the back door glass with non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using a new back door glass, clean the back door glass with non-residue solvent.




Hide 10.CLEAN VEHICLE BODY

B106081
0.5,1.292 0.75,0.75 0.75,0.75 0.833,0.75 true 2.26,1.438 2.583,0.75 2.583,0.75 2.667,0.75 true 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.865,0.667 1.219,0.917 0.354,0.25 10 false *1 2.698,0.667 3.031,0.927 0.333,0.26 10 false *1 0.729,1.781 1,2 0.271,0.219 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


a.

Using a scraper, remove the moulding and adhesive from the back door glass.


b.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.