Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (see page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
1.INSTALL QUARTER WINDOW ASSEMBLY LH
| *1 | Primer M |
| *2 | Adhesive |
| *a | CORRECT |
| *b | INCORRECT |
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Using a brush or sponge, apply Primer G to the contact surface of a new quarter window glass.
| *1 | Primer G | *2 | Adhesive Center Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 13.0 mm (0.512 in.) |
| b | 22.2 mm (0.874 in.) |
| c | 6.0 mm (0.236 in.) |
| d | 8.0 mm (0.315 in.) |
| e | 7.0 mm (0.276 in.) |
If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Apply adhesive to the quarter window glass.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off a tip of the cartridge nozzle as shown in the illustration.
| *1 | Adhesive | *2 | Adhesive Center Line |
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 13.0 mm (0.512 in.) |
| d | 22.2 mm (0.874 in.) |
| e | 6.0 mm (0.236 in.) |
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load a sealer gun with the cartridge.
Apply adhesive to the quarter window glass as shown in the illustration.
Install the quarter window glass to the vehicle body.
Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.
Allow the primer coating to dry for 3 minutes or more.
Check that the clips are attached to the body correctly.
Check the clearance between the body and glass.
Lightly press the outer surface of the glass to ensure a close fit.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to any areas where the amount of adhesive is inadequate.
Do not drive the vehicle within the time written in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
2.CHECK FOR LEAKS AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
3.INSTALL ROOF HEADLINING ASSEMBLY
4.INSTALL ASSIST GRIP
5.INSTALL INNER UPPER ROOF SIDE GARNISH LH
6.INSTALL QUARTER PILLAR GARNISH LH
7.INSTALL QUARTER INSIDE TRIM BOARD LH
8.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
9.INSTALL REAR DOOR SCUFF PLATE LH
10.INSTALL BACK DOOR SCUFF PLATE
11.INSTALL REAR NO. 2 SEAT ASSEMBLY LH