Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068710 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR NO. 2 SEAT ASSEMBLY LH

Hide 4.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Partially remove the rear door opening trim LH so that the quarter inside trim board LH and quarter pillar garnish LH can be removed (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 7.REMOVE INNER UPPER ROOF SIDE GARNISH LH

Hide 9.REMOVE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining (see page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the quarter window can be removed.



Hide 10.REMOVE QUARTER WINDOW ASSEMBLY LH

HINT:

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


NOTICE:

When separating the quarter window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.


B289599
1.583,2.583 1.99,2.927 0.406,0.344 10 false *a 0.146,1.375 0.458,1.688 0.313,0.313 10 false A 0.875,1.135 1.198,1.49 0.323,0.354 10 false A 0.771,2.531 1.323,2.958 0.552,0.427 10 false A - A
*a Cut


a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



c.
B289600
1.958,0.188 1.427,0.188 1.427,0.188 1.427,0.615 true 1.646,3.177 1.646,3.344 false 2.417,3.104 2.688,2.542 2.688,2.542 2.813,2.542 true 0.698,2.958 0.292,2.354 0.292,2.354 0.448,2.354 true 2.969,3.865 3.198,3.948 3.198,3.948 3.198,3.99 true 1.115,4.01 0.938,4.208 0.938,4.208 0.875,4.208 true 2.021,0.104 2.281,0.385 0.26,0.281 10 false *1 1.563,3.396 1.854,3.76 0.292,0.365 10 false *3 2.875,2.458 3.323,2.771 0.448,0.313 10 false *2 3.125,4.052 3.406,4.417 0.281,0.365 10 false *2 0.667,4.135 1.073,4.521 0.406,0.385 10 false *2 0.521,2.281 0.854,2.573 0.333,0.292 10 false *2
*1 Protective Tape
*2 Clip
*3 Piano Wire


for Glass Antenna Type:

Disconnect the connectors.


d.

From the interior, insert a piano wire between the vehicle body and the quarter window glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


f.

Cut through the adhesive by pulling the piano wire around the quarter window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the quarter window glass.



g.

Using suction cups, remove the quarter window assembly LH.


Hide 11.CLEAN QUARTER WINDOW ASSEMBLY LH

BO04421

a.

Clean the outer edges of the glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Ever if using new glass, clean the glass with non-residue solvent.




Hide 12.CLEAN VEHICLE BODY

B106081
0.5,1.292 0.75,0.75 0.75,0.75 0.833,0.75 true 2.26,1.438 2.583,0.75 2.583,0.75 2.667,0.75 true 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.865,0.667 1.219,0.917 0.354,0.25 10 false *1 2.698,0.667 3.031,0.927 0.333,0.26 10 false *1 0.729,1.781 1,2 0.271,0.219 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

Use a knife to cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.