2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
If DTC P0011 or P0012 is output, check the Variable Valve Timing (VVT) system.

The VVT system includes the ECM, oil control valve and VVT controller. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.
A192077E04
DTC No.
DTC Detection Condition
Trouble Area
P0011
Valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM
P0012
Valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM

WIRING DIAGRAM

Refer to DTC P0010 (Click here).

INSPECTION PROCEDURE

HINT:
  1. DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC remains stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil filter.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0011 or P0012 is output
    A
    DTC P0011 or P0012 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

  1. Check the engine speed when the camshaft timing oil control valve is operated using the intelligent tester when the engine coolant temperature is 50°C (122°F) or less.

    HINT:
    1. When performing the Active Test, make sure the air conditioning is on.
    2. Make sure the engine coolant temperature when the engine is started is 30°C (86°F) or less.


    OK:
    Tester Operation
    Specified Condition
    Camshaft timing oil control valve OFF
    Normal engine speed
    Camshaft timing oil control valve ON
    Engine idles roughly or stalls soon after camshaft timing oil control valve switched from OFF to ON



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Allow the engine to idle for more than 1 minute.

  1. Drive the vehicle for more than 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0011 or P0012 is output
    B

    HINT:
    DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes remain stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil control valve filter, thus eliminating the source of the problem.



B
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).

  1. A183795E07
    Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the camshaft timing oil control valve assembly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Inspect the camshaft timing gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


6. INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.

  1. Reinstall the oil control valve filter.



NG
REPLACE OIL CONTROL VALVE FILTER
OK


7. ADJUST VALVE TIMING

HINT:
There are no marks on the cylinder head to align for the purpose of checking valve timing. Valve timing can only be inspected by aligning the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to align the timing marks (Click here).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Allow the engine to idle for more than 1 minute.

  1. Drive the vehicle for more than 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0011 or P0012 is output
    B

    HINT:
    DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes remain stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil control valve filter, thus eliminating the source of the problem.



B
REPLACE ECM (Click here)
A

END


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (from Aug 2013)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012) (from Aug 2014) →