2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

HINT:
This DTC relates to the oil control valve.

The Variable Valve Timing (VVT) system includes the ECM, intake camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty cycle control signal to the intake camshaft timing oil control valve assembly. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the intake camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the intake camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.
A192077E04
DTC No.
DTC Detection Condition
Trouble Area
P0010
An open or short in the camshaft timing oil control valve circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve circuit
  2. Camshaft timing oil control valve assembly
  3. ECM

WIRING DIAGRAM

A133814E16

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

  1. Check the engine speed when the camshaft timing oil control valve is operated using the intelligent tester when the engine coolant temperature is 50°C (122°F) or less.

    HINT:
    1. When performing the Active Test, make sure the air conditioning is on.
    2. Make sure the engine coolant temperature when the engine is started is 30°C (86°F) or less.


    OK:
    Tester Operation
    Specified Condition
    Camshaft timing oil control valve OFF
    Normal engine speed
    Camshaft timing oil control valve ON
    Engine idles roughly or stalls soon after camshaft timing oil control valve switched from OFF to ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).

  1. A183795E07
    Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the camshaft timing oil control valve assembly.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C54-2 (+) - C62-14 (OC1+)
    Always
    Below 1 Ω
    C54-1 (-) - C62-9 (OC1-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C54-2 (+) or C62-14 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C54-1 (-) or C62-9 (OC1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the camshaft timing oil control valve assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012) (Aug 2013 – Jul 2014) →