2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P0335 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviations in the crankshaft and camshaft position sensor 1 signals (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly
  3. Oil control valve assembly filter
  4. Camshaft timing gear assembly
  5. ECM
P0018
Deviations in the crankshaft and camshaft position sensor 2 signals (2 trip detection logic).

WIRING DIAGRAM

Refer to DTC P0335 (Click here).
Refer to DTC P0340 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0016 or P0018
    A
    P0016 or P0018 and other DTCs
    B



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.

    OK:
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls soon after camshaft timing oil control valve assembly switched from off to on



NG
Go to step 4
OK


3. CHECK ENGINE MECHANICAL SYSTEM
  1. Check the engine mechanical system (Click here).



NEXT
Go to step 7
4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2)
  1. Inspect the camshaft timing oil control valve assembly (for Intake Side of Bank 1, 2) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2) (Click here)
OK


5. INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

  1. A225778E02
    Remove the No. 1 oil pipe or No. 2 oil pipe.

  1. Remove the oil control valve filter RH or oil control valve filter LH.

  1. Check that the oil control valve filter and oil pipe are not clogged.

    OK:
    The oil control valve filter and oil pipe are not clogged.

    Text in Illustration 
    *A
    Bank 2
    *B
    Bank 1

  1. Reinstall the oil control valve filter RH or oil control valve filter LH.

  1. Reinstall the No. 1 oil pipe or No. 2 oil pipe.



NG
REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE
OK


6. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. In order to clear the ECM learned values for valve timing, disconnect the cable from the negative (-) battery terminal for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the DTCs.

    OK:
    DTCs are not output.



NG
REPLACE ECM (Click here)
OK

END


← P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0018) (Aug 2013 – Jul 2014)P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) (+ P0019) (Aug 2013 – Jul 2014) →