2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A192077E04
DTC Code
DTC Detection Condition
Trouble Area
P0010
An open or short in the camshaft timing oil control valve assembly (for intake side of bank 1) circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve assembly (for intake side of bank 1) circuit
  2. Camshaft timing oil control valve assembly (for intake side of bank 1)
  3. ECM
P0020
An open or short in the camshaft timing oil control valve assembly (for intake side of bank 2) circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve assembly (for intake side of bank 2) circuit
  2. Camshaft timing oil control valve assembly (for intake side of bank 2)
  3. ECM

WIRING DIAGRAM

A227098E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC
  1. Clear the DTC after recording the freeze frame data and DTC.

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check for DTC.

  1. Check that P0010 or P0020 is output.

    OK:
    P0010 or P0020 is output.



NG
CHECK FOR INTERMITTENT PROBLEMS (Click here)
OK


2. INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2)
  1. Inspect the camshaft timing oil control valve assembly (for Intake Side of Bank 1, 2) (Click here).



NG
REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
  1. Reconnect the camshaft timing oil control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C16-1 - C35-19 (OC1+)
    Always
    Below 1 Ω
    C18-1 - C34-19 (OC2+)
    Always
    Below 1 Ω
    C16-2 - C35-20 (OC1-)
    Always
    Below 1 Ω
    C18-2 - C34-20 (OC2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C16-1 or C35-19 (OC1+) - Body ground
    Always
    10 kΩ or higher
    C18-1 or C34-19 (OC2+) - Body ground
    Always
    10 kΩ or higher
    C16-2 or C35-20 (OC1-) - Body ground
    Always
    10 kΩ or higher
    C18-2 or C34-20 (OC2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the camshaft timing oil control valve assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (+ P0020) (Aug 2013 – Jul 2014)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (Aug 2013 – Jul 2014) →