P0230 Fuel Pump Primary Circuit
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed among 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0230 |
Either condition is met (1 trip detection logic):
|
|
MONITOR DESCRIPTION
To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V and approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Body / (desired system) / DTC.
Read the DTCs.
Result Result
Proceed to
DTC B1500 is not output
A
DTC B1500 is output
B
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the fuel pump / Speed.
Check whether operating sounds can be heard while operating the relay using the tester.
- OK:
- Operating sounds can be heard from circuit opening relay (C/OPN).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND) |
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
S8-1 (FPC) - G55-3 (FPC)
Always
Below 1 Ω
S8-2 (DI) - G56-26 (DI)
Always
Below 1 Ω
S8-3 (E) - Body ground
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
S9-2 (FP-) - Body ground
Always
10 kΩ or higher
S8-1 (FPC) or G55-3 (FPC) - Body ground
Always
10 kΩ or higher
S8-2 (DI) or G56-26 (DI) - Body ground
Always
10 kΩ or higher
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 4. REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS |
Check that there are 17 liters or more of fuel remaining.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and idle it for 5 minutes.
Drive the vehicle in an urban area for approximately 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
No output
A
DTC P0230 is output
B
|
|
||||
| A | ||
| ||
| 6. INSPECT CIRCUIT OPENING RELAY (C/OPN) |
Inspect the circuit opening relay (C/OPN) (Click here).
|
|
||||
| OK | |
| 7. INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE) |
![]() ![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C/OPN relay terminal 2 - Body ground
Ignition switch ON
11 to 14 V
C/OPN relay terminal 5 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *1
Engine Room Relay Block
*2
Circuit Opening Relay (C/OPN)
Reinstall the circuit opening relay (C/OPN).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU) |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C/OPN relay terminal 1 - G56-8(FC)
Always
Below 1 Ω
C/OPN relay terminal 3 - S8-4 (+B)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C/OPN relay terminal 1 or G56-8 (FC) - Body ground
Always
10 kΩ or higher
C/OPN relay terminal 3 or S8-4 (+B) - Body ground
Always
10 kΩ or higher
Reinstall the circuit opening relay (C/OPN).
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU) |
Disconnect the fuel sender gauge connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
S5-4 (B2) - S9-1 (FP)
Always
Below 1 Ω
S5-5 (E2) - S9-2 (FP-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
S5-4 (B2) or S9-1 (FP) - Body ground
Always
10 kΩ or higher
S5-5 (E2) or S9-2 (FP-) - Body ground
Always
10 kΩ or higher
Reconnect the fuel sender gauge connector.
Reconnect the fuel pump ECU connector.
|
|
||||
| OK | |
| 10. INSPECT FUEL PUMP |
Inspect the fuel pump (for Single Tank Type) (Click here).
Inspect the fuel pump (for Double Tank Type) (Click here).
Result Test Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | |
| 11. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND) |
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
S8-1 (FPC) - G55-3 (FPC)
Always
Below 1 Ω
S8-2 (DI) - G56-26 (DI)
Always
Below 1 Ω
S8-3 (E) - Body ground
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
S8-1 (FPC) or G55-3 (FPC) - Body ground
Always
10 kΩ or higher
S8-2 (DI) or G56-26 (DI) - Body ground
Always
10 kΩ or higher
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 12. REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 13. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and idle it for 5 minutes.
Drive the vehicle in an urban area for approximately 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
No output
A
DTC P0230 is output
B
|
|
||||
| A | ||
| ||
| 14. CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - NO. 1 INTEGRATION RELAY) |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C/OPN relay terminal 2 - 1A-5
Always
Below 1 Ω
C/OPN relay terminal 5 - 1B-4
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C/OPN relay terminal 2 or 1A-5 - Body ground
Always
10 kΩ or more
C/OPN relay terminal 5 or 1B-4 - Body ground
Always
10 kΩ or more
Reinstall the circuit opening relay (C/OPN).
Reinstall the No. 1 integration relay.
|
|
||||
| OK | ||
| ||

