2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the No. 1 integration relay (EFI) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A266627E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
A223349E02
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT NO. 1 INTEGRATION RELAY (EFI AND IG2)
  1. Inspect the EFI relay (Click here).

  1. Inspect the IG2 relay (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
  1. Check the harness and connectors between the No. 1 integration relay and ECM.

    1. Remove the No. 1 integration relay from the engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      Tester Connection
      Condition
      Specified Condition
      G55-9 (MREL) - 1B-2
      Always
      Below 1 Ω
      G55-22 (+B) - 1B-4
      Always
      Below 1 Ω
      G55-23 (+B2) - 1B-4
      Always
      Below 1 Ω

      Standard Resistance (Check for Short):
      Tester Connection
      Condition
      Specified Condition
      G55-9 (MREL) or 1B-2 - Body ground
      Always
      10 kΩ or higher
      G55-22 (+B) or 1B-4 - Body ground
      Always
      10 kΩ or higher
      G55-23 (+B2) or 1B-4 - Body ground
      Always
      10 kΩ or higher

    4. Reinstall the No. 1 integration relay.

    5. Reconnect the ECM connector.

  1. Check the harness and connectors between the No. 1 integration relay and body ground.

    1. Remove the No. 1 integration relay from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      Tester Connection
      Condition
      Specified Condition
      1B-3 - Body ground
      Always
      Below 1 Ω

    3. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C36-12 (E1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW VOLTAGE)
A177861E37
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G56-21 (IGSW) - C36-12 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 6
OK

REPLACE ECM (Click here)

6. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1A-5 - G56-21 (IGSW)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1A-5 or G56-21 (IGSW) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the No. 1 integration relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result 
Result
Proceed to
w/ Entry and Start System
A
w/o Entry and Start System
B


B
Go to step 10
A


8. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G50-8 (IG2D) - 1A-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G50-8 (IG2D) or 1A-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the No. 1 integration relay.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)
  1. Check the entry and start system (Click here).



NG
REPAIR ENTRY AND START SYSTEM (Click here)
OK

REPLACE ECM (Click here)

10. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G2-6 (IG2) - 1A-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G2-6 (IG2) or 1A-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the No. 1 integration relay.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (from Aug 2014)ECM Power Source Circuit (from Aug 2014) →