B1500 Fuel Sender Open Detected
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when the combination meter detects a fuel sender gauge malfunction.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1500 |
When the combination meter detects a fuel sender gauge malfunction. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE) |
Operate the intelligent tester according to the display and select the Data List (Click here).
Combination Meter Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Fuel Input
Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5
Fuel sender input value
Unit: L
- OK:
- Fuel amount value displayed on the intelligent tester is almost the same as needle indication.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE AND BODY GROUND) |
Disconnect the G6 meter connector.
Disconnect the S5 gauge connector.
Disconnect the R40 gauge connector*.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G6-9 (L) - S5-2 (FS)
Always
Below 1 Ω
G6-24 (E) - S5-3 (FE)
G6-9 (L) - R40-3*
G6-24 (E) - R40-1*
G6-21 (E2) - Body ground
- *: for 3 Door
|
|
||||
| OK | |
| 3. CHECK ENGINE TYPE |
Check the engine type.
Engine Type Engine type
Proceed to
for 1GR-FE
A
for 2TR-FE
B
for 1KD-FTV
C
for 5L-E
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 4. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1GR-FE) |
Remove the fuel sender gauge.

- for 1GR-FE, Single Tank Type: (Click here)
- for 1GR-FE, Double Tank Type: (Click here)
- for 1GR-FE, Single Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Text in Illustration *a
Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
*b
Lower side (to Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | |
| 5. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1GR-FE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Front view of wire harness connector (to Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 6. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 2TR-FE) |
![]() ![]() |
- NOTICE:
- For 3 door vehicles, proceed to next step.
Remove the fuel sender gauge.
- for 2TR-FE, Single Tank Type: (Click here)
- for 2TR-FE, Double Tank Type: (Click here)
- for 2TR-FE, Single Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Text in Illustration *a
Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
*b
Lower side (to Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | |
| 7. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 2TR-FE) |
Remove the fuel sender gauge (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 3
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Component without harness connected (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Front view of wire harness connector (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 8. CHECK FUEL TANK TYPE |
Check the fuel tank type.
Fuel Tank Type Fuel Tank Type
Proceed to
Single tank type
A
Double tank type
B
|
|
||||
| A | |
| 9. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE) |
![]() ![]() |
- NOTICE:
- For 3 door vehicles, proceed to next step.
Remove the fuel sender gauge.
- for 1KD-FTV, Single Tank Type: (Click here)
- for 1KD-FTV, Single Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Text in Illustration *a
Component without harness connected (Fuel Tank Vent Tube Assembly)
*b
Lower side (to Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B
|
|
||||
| OK | |
| 10. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE) |
Remove the fuel sender gauge.
- for 1KD-FTV, Single Tank Type: (Click here)
- for 1KD-FTV, Single Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 3
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Component without harness connected (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Front view of wire harness connector (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
|
|
||||
| OK | ||
| ||
| 11. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE) |
![]() ![]() |
Remove the fuel sender gauge.
- for 1KD-FTV, Double Tank Type: (Click here)
- for 1KD-FTV, Double Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Text in Illustration *a
Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
*b
Lower side (to Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
| OK | |
| 12. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Front view of wire harness connector (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
| OK | ||
| ||
| 13. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 5L-E) |
![]() ![]() |
Remove the fuel sender gauge.
- for 5L-E, Single Tank Type: (Click here)
- for 5L-E, Double Tank Type: (Click here)
- for 5L-E, Single Tank Type: (Click here)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-2 (FS) - B-2
Always
Below 1 Ω
A-3 (FE) - B-1
Text in Illustration *a
Component without harness connected (Fuel Tank Vent Tube Assembly)
*b
Lower side (Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | |
| 14. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 5L-E) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration *a
Front view of wire harness connector (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
Result Result
Proceed to
OK
A
NG (for Single Tank Type)
B
NG (for Double Tank Type)
C
|
|
||||
|
|
||||
| A | ||
| ||
