Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM (w/o DPF)
ECM Power Source Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here ) and initialization (Click here ).
1. INSPECT NO. 1 INTEGRATION RELAY (NO. 1 INTEGRATION RELAY - BODY GROUND)
Remove the No. 1 integration relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
1C-1 - Body ground
Always
11 to 14 V
*1
Engine Room Relay Block
*a
Front view of wire harness connector (to No. 1 integration Relay)
Reinstall the integration relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
2. INSPECT NO. 1 INTEGRATION RELAY (EFI , IG2)
Inspect the No. 1 integration relay (EFI) (Click here ).
Inspect the No. 1 integration relay (IG2) (Click here ).
NG
REPLACE NO. 1 INTEGRATION RELAY
OK
3. INSPECT ECM (IGSW VOLTAGE)
Turn the ignition switch to ON.
Measure the resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G58-24 (IGSW) - C93-1 (E1)
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Component with harness connected (to ECM)
Result
Result
Proceed to
OK
A
NG (w/ Entry and Start System)
B
NG (w/o Entry and Start System)
C
B
C
A
4. CHECK WIRE HARNESS (NO. 1 INTEGRATION RELAY - ECM)
Check the wire harness between the ECM and No. 1 integration relay.
Disconnect the ECM connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G58-11 (MREL) - 1B-2
Always
Below 1 Ω
G57-24 (+B) - 1B-4
Always
Below 1 Ω
G57-17 (+B2) - 1B-4
Always
Below 1 Ω
G58-24 (IGSW) - 1A-5
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
G58-11 (MREL) or 1B-2 - Body ground
Always
10 kΩ or higher
G57-24 (+B) or 1B-4 - Body ground
Always
10 kΩ or higher
G57-17 (+B2) or 1B-4 - Body ground
Always
10 kΩ or higher
G58-24 (IGSW) or 1A-5 - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reinstall the No. 1 integration relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. CHECK WIRE HARNESS (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
Remove the power management control ECU.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G50-8 (IG2D) - 1A-1
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
G50-8 (IG2D) or 1A-1 - Body ground
Always
10 kΩ or higher
Reinstall the power management control ECU.
Reinstall the No. 1 integration relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6. CHECK WIRE HARNESS (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
Disconnect the ignition switch assembly connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G2-6 (IG2) - 1A-1
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
G2-6 (IG2) or 1A-1 - Body ground
Always
10 kΩ or higher
Reconnect the ignition switch assembly connector.
Reinstall the No. 1 integration relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. INSPECT IGNITION SWITCH ASSEMBLY
Inspect the ignition switch assembly (Click here ).
NG
REPAIR OR REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)