51 Stop Light Switch Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.The stop light switch has a duplex system (signals STP and ST1-) to recognize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.
- HINT:
- The normal condition is shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
Off
On
On
ST1-
On
On
Off
DTC No.
DTC Detection Condition
Trouble Area
51
Conditions (a), (b) and (c) continue for 0.5 seconds or more(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is off when ST1- signal is off.
- Open or short in stop light switch signal circuit
- Stop light switch
- ECM
- Open or short in stop light switch signal circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
Disconnect the stop light switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A85-1 (B) - Body ground
Always
11 to 14 V
A85-5 (B) - Body ground
Ignition switch ON
11 to 14 V
*a
Front view of wire harness connector
(to Stop Light Switch Assembly)
Reconnect the stop light switch assembly connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND) |
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A85-3 (GND) - Body ground
Always
Below 1 Ω
Reconnect the stop light switch assembly connector.
|
|
||||
| OK | |
| 3. CHECK ECM (STP, ST1- VOLTAGE) |
Turn the ignition switch to ON.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Brake Pedal Condition
Specified Condition
G61-19 (STP) - C101-14 (E1)
Depressed
11 to 14 V
Released
Below 1.5 V
G62-11 (ST1-) - C101-14 (E1)
Depressed
Below 1.5 V
Released
11 to 14 V
Text in Illustration *a
Brake pedal depressed
*b
Brake pedal released
*c
Component with harness connected
(ECM)
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR |
Disconnect the stop light switch assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A85-2 - G61-19 (STP)
Always
Below 1 Ω
A85-4 - G62-11 (ST1-)
Always
Below 1 Ω
A85-2 or G61-19 (STP) - Body ground
Always
10 kΩ or higher
A85-4 or G62-11 (ST1-) - Body ground
Always
10 kΩ or higher
Reconnect the stop light switch assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
