2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

51 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.
The stop light switch has a duplex system (signals STP and ST1-) to recognize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:
The normal condition is shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
Off
On
On
ST1-
On
On
Off
DTC No.
DTC Detection Condition
Trouble Area
51
Conditions (a), (b) and (c) continue for 0.5 seconds or more(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is off when ST1- signal is off.
  1. Open or short in stop light switch signal circuit
  2. Stop light switch
  3. ECM


WIRING DIAGRAM

A311394E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE)

  1. E233265E83
    Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A85-1 (B) - Body ground
    Always
    11 to 14 V
    A85-5 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - INTEGRATION RELAY, BATTERY)
OK


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A85-3 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (STP, ST1- VOLTAGE)

  1. A110540E06
    Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    G61-19 (STP) - C101-14 (E1)
    Depressed
    11 to 14 V
    Released
    Below 1.5 V
    G62-11 (ST1-) - C101-14 (E1)
    Depressed
    Below 1.5 V
    Released
    11 to 14 V

    Text in Illustration 
    *a
    Brake pedal depressed
    *b
    Brake pedal released
    *c
    Component with harness connected
    (ECM)



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A85-2 - G61-19 (STP)
    Always
    Below 1 Ω
    A85-4 - G62-11 (ST1-)
    Always
    Below 1 Ω
    A85-2 or G61-19 (STP) - Body ground
    Always
    10 kΩ or higher
    A85-4 or G62-11 (ST1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LAMP SWITCH ASSEMBLY (Click here)


← 51 Stop Light Switch Circuit Malfunction (Aug 2013 – Jul 2014)Pre-heating Control Circuit (Aug 2013 – Jul 2014) →