2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0443 Evaporative Emission Control System Purge Control Valve Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signal sent to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC No.
DTC Detection Condition
Trouble Area
P0443
The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM

A227122E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

  1. A225197E03
    Connect the intelligent tester to the DLC3.

  1. Remove the vacuum hose of the purge VSV from the charcoal canister.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. When the purge VSV is operated using the intelligent tester, check whether the disconnected hose applies suction to your finger.

    OK:
    Tester Operation
    Specified Condition
    VSV is ON
    Disconnected hose applies suction to finger
    VSV is OFF
    Disconnected hose applies no suction to finger

    Text in Illustration 
    *1
    Purge VSV
    *2
    Hose (to Canister)



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT PURGE VSV
  1. Inspect the purge VSV (Click here).



NG
REPLACE PURGE VSV (Click here)
OK


3. INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
A107917E74
  1. Disconnect the purge VSV connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C15-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Purge VSV)

  1. Reconnect the purge VSV connector.



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
  1. Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance between the terminals of the wire harness side connectors.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C15-2 - C36-18 (PRG)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C15-2 or C36-18 (PRG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the purge VSV connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
  1. Disconnect the purge VSV connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C15-1 - 1B-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C15-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the purge VSV connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT COMPONENTS


← P0420 Catalyst System Efficiency Below Threshold (Bank 1) (+ P0430) (from Aug 2014)P0443 Evaporative Emission Control System Purge Control Valve Circuit (from Aug 2014) →