P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- P0977 Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Shifting from 1st to 4th is performed in combination with the ON and OFF operation of shift solenoid valves S1 and S2, which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely. Also, the ECM stops sending current to the open or short-circuited solenoid (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0976 |
ECM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection logic). |
|
| P0977 |
ECM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip detection logic). |
|
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in either shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S2 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S2 circuit.When shift solenoid valve S2 is OFF, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S2 circuit (Click here).
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Shift solenoid valve S2 is turned ON/OFF normally when the shift lever is in D.
ECM gear shift command
1st
2nd
3rd
4th
Shift solenoid valve S2
OFF
ON
ON
OFF
| 1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2) |
Disconnect the C58 transmission wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
8 (S2) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Component without harness connected
(Transmission Wire)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
Disconnect the C62 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C62-22 (S2) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Rear view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 3. INSPECT SHIFT SOLENOID VALVE S2 |
Remove shift solenoid valve S2.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S2 connector
- Battery negative (-) → Shift solenoid valve S2 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S2 connector
| *a |
Component without harness connected (Shift Solenoid Valve S2) |
|
|
||||
| OK | ||
| ||
