2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSPECTION

Inspection · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


INSPECT FUEL INJECTOR ASSEMBLY
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the fuel injector assembly.


INSPECT INJECTION VOLUME AND LEAKAGE

  1. Check the injection volume.

    CAUTION:
    This test involves high-pressure fuel and electricity, therefore, safety precautions should be taken. Perform this test in a safe area and avoid any sparks and flames. Do not smoke.


    1. Discharge the fuel system pressure (Click here).

    2. Remove the fuel hose from the fuel pressure pulsation damper (Click here).

    3. Remove the fuel hose from the fuel filter (Click here).

    4. Disconnect the fuel pressure regulator (Click here).

      NOTICE:
      Do not disconnect the No. 2 fuel hose.

    5. A273785E01
      Assemble SST as shown in the illustration.
      SST
      09268-31014   (09268-41091, 09268-41110, 09268-41120, 09268-41310, 09268-41500, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      SST (Union)
      *2
      SST (Hose Band)
      *3
      SST (Fuel Tube Connector)
      *4
      SST (3 Way)
      *5
      SST (Hose)
      *6
      SST (Adapter)
      *7
      Fuel Pressure Regulator
      *8
      Fuel Injector
      *9
      SST (Clamp)
      *10
      Fuel Filter

    6. A264461E01
      Connect SST to the fuel filter.
      SST
      09268-31014   (09268-41500)
      Text in Illustration 
      *1
      SST (Fuel Tube Connector)
      *2
      Fuel Filter

    7. A264462E01
      Install the pressure regulator to SST (union) with the 2 bolts.
      SST
      09268-31014   (09268-41091, 09268-41700, 95336-08070)

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Hose Band)
      *3
      SST (Union)
      *4
      SST (Hose)

      NOTICE:
      Make sure that the O-ring is installed to the pressure regulator.

    8. Install the O-ring to the injector.

    9. A264463E01
      Assemble SST as shown in the illustration.
      SST
      09268-31014   (09268-41110, 09268-41310, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      Vinyl Tube
      *2
      SST (Clamp)
      *3
      SST (Hose)
      *4
      SST (Hose Band)
      *5
      SST (Adaptor)

    10. A264464E01
      Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).
      SST
      09268-31014   (09268-41800)
      Text in Illustration 
      *1
      SST (Tie Band)
      *2
      Lock

      NOTICE:
      1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
      2. Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

      HINT:
      When removing SST (tie band), disengage the lock.

    11. Check that SST (clamp) and SST (adapter) cannot be easily separated.

    12. Put the injector into a graduated cylinder.

      CAUTION:
      Install a suitable vinyl tube to the injector to contain any gasoline spray.

    13. Operate the fuel pump (Click here).

    14. A264465E01
      Connect SST (wire) to the injector and the battery for 15 seconds and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.
      SST
      09842-30080  

      Standard injection volume:
      71 to 86 cm3 (4.3 to 5.2 cu in.) per 15 seconds

      Difference between each injector:
      15 cm3 (0.9 cu in.) or less

      Text in Illustration 
      *1
      SST (Wire)
      V100135
      Connect

      NOTICE:
      1. Make sure that SST (EFI inspection wire H) is securely connected.
      2. Always do the switching at the battery side.

      If the injection volume is not as specified, replace the injector.

  1. Check the leakage.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check the fuel leakage from the injector.

      Fuel leakage:
      1 drop or less in 12 minutes

← REMOVAL (from Aug 2014)INSPECTION (from Aug 2014) →