2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

MIL Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually; when the ignition switch is first turned to ON, the MIL turns on and then off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A182518E08

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK THAT MIL IS ILLUMINATED
  1. Turn the ignition switch to ON.

  1. Check the illumination condition of the MIL.

    Result 
    Condition
    Proceed to
    MIL remains illuminated (Even after ignition switch turned to ON and several seconds have passed, MIL still remains illuminated)
    A
    MIL remains off (Does not illuminate at all)
    B
    MIL illuminates for several seconds, but turns off after engine is started
    C



B
Go to step 5

C
SYSTEM OK
A


2. CHECK WHETHER MIL TURNS OFF
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check if any DTCs are output. Note down any DTCs.

  1. Clear the DTCs (Click here).

  1. Check if the MIL goes off.

    OK:
    MIL goes off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G7-7 (CHK) or G59-13 (W) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK THAT ENGINE STARTS
  1. Turn the ignition switch to ON.

  1. Check that the engine starts.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The intelligent tester cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


6. CHECK COMBINATION METER ASSEMBLY
A177861E30
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G59-13 (W) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 7
OK

REPLACE ECM (Click here)

7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G7-7 (CHK) - G59-13 (W)
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Brake Override System (from Aug 2013)MIL Circuit (from Aug 2014) →