2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

VC Output Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM constantly generates a 5 V power supply voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.
A206916E15
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON, and then goes off when the engine starts.


WIRING DIAGRAM

A285432E01

INSPECTION PROCEDURE


1. CHECK MIL CONDITION
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up.



NG
Go to step 2
OK

SYSTEM OK

2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Check the communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle body with motor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body with motor assembly connector.



A
REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE POSITION SENSOR) (Click here)
B


4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal sensor assembly connector.



A
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR) (Click here)
B


5. CHECK MIL (AIR PRESSURE SENSOR)
  1. Disconnect the air pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the air pressure sensor connector.



A
REPLACE AIR PRESSURE SENSOR (Click here)
B


6. CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body with motor assembly connector.

  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the air pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C61-10 (VCTA) - Body ground
    Always
    10 kΩ or higher
    G60-4 (VCPA) - Body ground
    Always
    10 kΩ or higher
    G60-3 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C62-6 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body with motor assembly connector.

  1. Reconnect the accelerator pedal sensor assembly connector.

  1. Reconnect the air pressure sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Power Source Circuit (from Aug 2013)VC Output Circuit (from Aug 2014) →