2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

MIL Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually: When the ignition switch is first turned to ON, the MIL should be illuminated, and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A182518E05

INSPECTION PROCEDURE


1. CHECK THAT MIL IS ILLUMINATED
  1. Check that the MIL is illuminated.

    Result 
    Result
    Proceed to
    MIL remains on
    A
    MIL does not illuminate
    B



B
Go to step 5
A


2. CHECK WHETHER MIL TURNS OFF
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check for DTCs (Click here). If DTCs are output, write them down.

  1. Clear the DTCs (Click here).

  1. Check that the MIL turns off.

    OK:
    MIL turns off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G7-7 (CHK) - G55-13 (W)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G7-7 (CHK) or G55-13 (W) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK THAT MIL IS ILLUMINATED
  1. Check if the MIL is illuminated when the ignition switch is turned to ON.

    OK:
    MIL is illuminated.



NG
Go to step 6
OK

SYSTEM OK

6. CHECK THAT ENGINE STARTS
  1. Turn the ignition switch to ON.

  1. Start the engine.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The intelligent tester cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


7. INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
  1. Refer to the combination meter troubleshooting procedure (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)


← Brake Override System (from Aug 2014)MIL Circuit (from Aug 2014) →