VC Output Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
|
|
||||
| B | |
| 2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and tester on.
Check the communication between the tester and ECM.
Result Result
Proceed to
Communication is possible
A
Communication is not possible
B
|
|
||||
| B | |
| 3. CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY) |
Disconnect the throttle body with motor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle body with motor assembly connector.
|
|
||||
| B | |
| 4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 5. CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1) |
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor (for Intake Side of Bank 1) connector.
|
|
||||
| B | |
| 6. CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2) |
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor (for Intake Side of Bank 2) connector.
|
|
||||
| B | |
| 7. CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1) |
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
|
|
||||
| B | |
| 8. CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2) |
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
|
|
||||
| B | |
| 9. CHECK MIL (POWER STEERING OIL PRESSURE SWITCH) |
Disconnect the power steering oil pressure switch connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the power steering oil pressure switch connector.
|
|
||||
| B | |
| 10. CHECK MIL (EMISSION CONTROL VALVE SET) |
Disconnect the emission control valve set connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the emission control valve set connector.
|
|
||||
| B | |
| 11. CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET) |
Disconnect the No. 2 emission control valve set connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the No. 2 emission control valve set connector.
|
|
||||
| B | |
| 12. CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Disconnect the emission control valve set connector.
Disconnect the No. 2 emission control valve set connector.
Disconnect the power steering oil pressure switch connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
G56-4 (VCPA) - Body ground
Always
10 kΩ or higher
G56-2 (VCP2) - Body ground
Always
10 kΩ or higher
C36-13 (VCTA) - Body ground
Always
10 kΩ or higher
C34-15 (VCV1) - Body ground
Always
10 kΩ or higher
C34-16 (VCV2) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connectors.
Reconnect the throttle body with motor assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the VVT sensor (for Intake Side of Bank 1) connector.
Reconnect the VVT sensor (for Intake Side of Bank 2) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Reconnect the emission control valve set connector.
Reconnect the No. 2 emission control valve set connector.
Reconnect the power steering oil pressure switch connector.
|
|
||||
| OK | ||
| ||
