2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Viscous Heater with Magnet Clutch Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the heater switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the heater switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E195921E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER (HEATER SWITCH)
  1. Use the Data List to check if the heater switch assembly is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IDLE UP/PWR HEAT Switch
    Heater switch assembly / ON or OFF
    ON: Heater switch assembly on
    OFF: Heater switch assembly off
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT HEATER SWITCH ASSEMBLY

  1. E166833E03
    Remove the heater switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (+S) - 3 (-S)
    Heater switch assembly on
    Below 1 Ω
    6 (+S) - 3 (-S)
    Heater switch assembly off
    10 kΩ or higher

  1. Apply battery voltage to the heater switch assembly connector and check that the heater switch assembly illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2 (IND+)
    Battery negative (-) → Terminal 6 (+S)
    LED illuminates



NG
REPLACE HEATER SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (HEATER SWITCH - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the G22 switch connector.

  1. Disconnect the G25 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G22-6 (+S) - G25-36 (SWVC)
    Always
    Below 1 Ω
    G22-6 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (HEATER SWITCH - BATTERY AND BODY GROUND)

  1. E200630E01
    Disconnect the G22 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G22-2 (IND+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G22-3 (-S) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Heater Switch Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)

  1. E202090E01
    Remove the VISCUS relay from the engine room No. 1 relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    VISCUS relay terminal 5 - Body ground
    Ignition switch ON
    11 to 14 V
    VISCUS relay terminal 2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    VISCUS Relay
    *a
    Component without relay installed
    (Engine Room No. 1 Relay Block, Junction Block)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT VISCOUS HEATER RELAY (VISCUS)

  1. E145138
    Remove the VISCUS relay from the engine room No. 1 relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE VISCOUS HEATER RELAY (VISCUS)
OK


7. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS WITH MAGNET CLUTCH HEATER)
  1. Remove the VISCUS relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the C94 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    VISCUS relay terminal 3 - C94-1
    Always
    Below 1 Ω
    VISCUS relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER)
  1. Remove the VISCUS relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the G25 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    VISCUS relay terminal 2 - G25-16 (MG+)
    Always
    Below 1 Ω
    VISCUS relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

  1. E167401
    Remove the viscous with magnet clutch heater assembly (Click here).

  1. Apply battery voltage to the viscous with magnet clutch heater assembly and check the operation of the viscous with magnet clutch heater assembly.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Body ground
    Viscous with magnet clutch heater assembly operating sound can be heard, and magnetic clutch hub and rotor lock.



NG
REPLACE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← Viscous Heater with Magnet Clutch Circuit (Aug 2013 – Jul 2014)Blower Motor Circuit (Aug 2013 – Jul 2014) →