2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.
  6. If DTC P0355 is output, check the No. 5 ignition coil assembly circuit.
  7. If DTC P0356 is output, check the No. 6 ignition coil assembly circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly, and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
A209715E03
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil assembly and ECM
  3. No. 1 to No. 6 ignition coil assembly
  4. ECM

  1. A112406E02
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.
    Item
    Content
    Terminal
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Setting
    2 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

A115898E09
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

WIRING DIAGRAM

A227109E02
A266623E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A203962E10
  1. Disconnect the ignition coil assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C7-4 (GND) - Body ground
    Always
    Below 1 Ω
    C8-4 (GND) - Body ground
    Always
    Below 1 Ω
    C9-4 (GND) - Body ground
    Always
    Below 1 Ω
    C10-4 (GND) - Body ground
    Always
    Below 1 Ω
    C11-4 (GND) - Body ground
    Always
    Below 1 Ω
    C12-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C7-1 (+B) - C7-4 (GND)
    Ignition switch ON
    11 to 14 V
    C8-1 (+B) - C8-4 (GND)
    Ignition switch ON
    11 to 14 V
    C9-1 (+B) - C9-4 (GND)
    Ignition switch ON
    11 to 14 V
    C10-1 (+B) - C10-4 (GND)
    Ignition switch ON
    11 to 14 V
    C11-1 (+B) - C11-4 (GND)
    Ignition switch ON
    11 to 14 V
    C12-1 (+B) - C12-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C7-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C8-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C9-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C10-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C11-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C12-2 (IGF) - C36-6 (IGF1)
    Always
    Below 1 Ω
    C7-3 (IGT1) - C36-24 (IGT1)
    Always
    Below 1 Ω
    C8-3 (IGT2) - C36-25 (IGT2)
    Always
    Below 1 Ω
    C9-3 (IGT3) - C36-26 (IGT3)
    Always
    Below 1 Ω
    C10-3 (IGT4) - C36-27 (IGT4)
    Always
    Below 1 Ω
    C11-3 (IGT5) - C36-28 (IGT5)
    Always
    Below 1 Ω
    C12-3 (IGT6) - C35-25 (IGT6)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C7-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C8-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C9-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C10-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C11-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C12-2 (IGF) or C36-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C7-3 (IGT1) or C36-24 (IGT1) - Body ground
    Always
    10 kΩ or higher
    C8-3 (IGT2) or C36-25 (IGT2) - Body ground
    Always
    10 kΩ or higher
    C9-3 (IGT3) or C36-26 (IGT3) - Body ground
    Always
    10 kΩ or higher
    C10-3 (IGT4) or C36-27 (IGT4) - Body ground
    Always
    10 kΩ or higher
    C11-3 (IGT5) or C36-28 (IGT5) - Body ground
    Always
    10 kΩ or higher
    C12-3 (IGT6) or C35-25 (IGT6) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coil assembly (among No. 1 to No. 6 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check the DTCs output on the tester.

    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil assembly DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (Aug 2013 – Jul 2014)P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ 5 more codes) (Aug 2013 – Jul 2014) →