2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0365 Camshaft Position Sensor "B" Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The exhaust camshaft's VVT sensor consists of a magnet and MRE (Magnetoresistive Element).
The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crank angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft rotation. Based on a combination of the VVT signals and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
There is no exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor for exhaust side circuit
  2. VVT sensor for exhaust side
  3. Exhaust camshaft
  4. ECM
P0367
P0392
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is less than 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor for exhaust side circuit
  2. VVT sensor for exhaust side
  3. Exhaust camshaft
  4. ECM
P0368
P0393
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is more than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor for exhaust side circuit
  2. VVT sensor for exhaust side
  3. Exhaust camshaft
  4. ECM

  1. A228079E01
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveforms are as shown.
    2. EV1+ and EV2+ are the VVT sensor signal, and NE+ is the crankshaft position sensor signal.
    3. The wavelength becomes shorter as the engine speed increases.
      Item
      Content
      Terminal
      NE+ - NE-
      EV1+ - EV1-
      EV2+ - EV2-
      Equipment Setting
      5 V/DIV.
      20 msec./DIV.
      Condition
      Idling with warm engine


WIRING DIAGRAM

A160377E07

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If no problem is found through by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.


1. CHECK VVT SENSOR FOR EXHAUST SIDE (SENSOR POWER SOURCE)

  1. A208648E28
    Disconnect the VVT sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    C23-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *A
    Bank 1
    *B
    Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor)

  1. Reconnect the VVT sensor connector.



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (EX+) - C34-13 (EV1+)
    Always
    Below 1 Ω
    C22-2 (EX-) - C34-14 (EV1-)
    Always
    Below 1 Ω
    C23-1 (EX+) - D34-18 (EV2+)
    Always
    Below 1 Ω
    C23-2 (EX-) - C34-17 (EV2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (EX+) or C34-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    C22-2 (EX-) or C34-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (EX+) or D34-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    C23-2 (EX-) or C34-17 (EV2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
OK


3. CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)

  1. BR03795E25
    Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR FOR EXHAUST SIDE (Click here)
OK


4. CHECK EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Check the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5. REPLACE VVT SENSOR FOR EXHAUST SIDE
  1. Replace the VVT sensor for exhaust side (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 AND/OR P0393)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC P0365, P0367, P0368, P0390, P0392 and/or P0393 are output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

REPAIR COMPLETED

7. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C22-3 (VC2) - C34-15 (VCV1)
    Always
    Below 1 Ω
    C23-3 (VC2) - C34-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C22-3 (VC2) or C34-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    C23-3 (VC2) or C34-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
OK

REPLACE ECM (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (from Aug 2014)P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ 5 more codes) (from Aug 2014) →