DTC CHECK / CLEAR
Troubleshooting · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| DTC CHECK/CLEAR (When Using Intelligent Tester) |
Check for DTCs.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Check the details of the DTCs (Click here).
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Clear the DTCs.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Clear the DTCs by following the prompts on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
| DTC CHECK/CLEAR (When Using SST Check Wire) |
Check for DTCs.

Text in Illustration *a
Front view of DLC3
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
- SST
- 09843-18040
Turn the ignition switch to ON.
Read the DTCs output from the ABS warning light in the combination meter.
- HINT:
- When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
- When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
- When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.
- If no code is output, inspect the TC and CG terminal circuit and ABS warning light circuit.
- When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
Trouble Area
See Procedure
TC and CG terminal circuit
Click here
ABS warning light circuit (Remains on)
Click here
ABS warning light circuit (Does not come on)
Click here
Codes are explained in the DTC chart.
ABS DTC ABS Warning Light Display
Intelligent Tester Display
11
C0278
12
C0279
13
C0273
14
C0274
21
C0226
22
C0236
23
C0246
24
C0256
25
C1225
31
C1401
C1405
C1409
32
C1402
C1406
C1410
33
C1403
C1407
C1411
34
C1404
C1408
C1412
35
C1413
36
C1414
37
C1337
38
C1415
39
C1416
41
C1241
C1417
43
C1243
44
C1419
C1420
C1442
45
C1245
46
C1421
C1422
C1423
C1424
49
C1425
C1426
51
C1427
C1428
59
C1203
67
C1429
C1430
C1431
68
C1268
91
C1361
94
U0073
95
U0124
97
C1381
A1*
U0114
- *: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.
- *: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
- HINT:
- If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.
Clear the DTCs.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration *a
Front view of DLC3
- SST
- 09843-18040
Turn the ignition switch to ON.
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
Remove SST from the terminals of the DLC3.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch to ON.
Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.