2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the power window regulator switch, front power window regulator motor, harness or connector.

WIRING DIAGRAM

B243404E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the front power window regulator motor is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Up SW
    Front passenger side power window manual up signal / ON or OFF
    ON: Front passenger side power window manual up switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down signal / ON or OFF
    ON: Front passenger side power window manual down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that power window regulator motor operates (Click here).

    P-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Passenger side power window
    OFF/UP/DOWN
    -

    OK:
    The power window regulator motor operates normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B215963E16
    Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BODY GROUND)

  1. B243351E01
    Disconnect the J1*1 or K10*2 power window regulator switch connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD: 
    Tester Connection
    Condition
    Specified Condition
    J1-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD: 
    Tester Connection
    Condition
    Specified Condition
    K10-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the J1*1 or K10*2 power window regulator switch connector.

  1. Disconnect the J7*1 or K7*2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD: 
    Tester Connection
    Condition
    Specified Condition
    J1-6 (UP) - J7-10 (UP)
    Always
    Below 1 Ω
    J1-7 (DOWN) - J7-7 (DOWN)
    Always
    Below 1 Ω
    J1-6 (UP) - Body ground
    Always
    10 kΩ or higher
    J1-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    for RHD: 
    Tester Connection
    Condition
    Specified Condition
    K10-6 (UP) - K7-10 (UP)
    Always
    Below 1 Ω
    K10-7 (DOWN) - K7-7 (DOWN)
    Always
    Below 1 Ω
    K10-6 (UP) - Body ground
    Always
    10 kΩ or higher
    K10-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY - BATTERY AND BODY GROUND)

  1. B243286E02
    Disconnect the J7*1 or K7*2 power window regulator motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD: 
    Tester Connection
    Condition
    Specified Condition
    J7-2 (B) - Body ground
    Always
    11 to 14 V
    for RHD: 
    Tester Connection
    Condition
    Specified Condition
    K7-2 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD: 
    Tester Connection
    Condition
    Specified Condition
    J7-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD: 
    Tester Connection
    Condition
    Specified Condition
    K7-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Motor Assembly)

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)


← Driver Side Power Window does not Operate with Power Window Master Switch (from Aug 2014)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Aug 2014) →