2013-2015 Land Cruiser Prado · Service Manual Brake

C1425 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU (master cylinder solenoid) inputs stop light switch signals and the condition of brake operation.
The skid control ECU (master cylinder solenoid) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC Code
DTC Detection Condition
Trouble Area
C1425
When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off, an open in the STP terminal circuit continues for 3 seconds or more.
  1. STP terminal circuit
  2. Stop light control ECU
  3. Stop light control ECU circuit
  4. Skid control ECU (Master cylinder solenoid)

WIRING DIAGRAM

C294402E01

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT STOP LIGHT CONTROL ECU ASSEMBLY
  1. Inspect the stop light control ECU assembly (Click here).



NG
REPLACE STOP LIGHT CONTROL ECU (Click here)
OK


4. CHECK TERMINAL VOLTAGE (STP)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. C214161E31
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Master Cylinder Solenoid])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (+ C1456) (from Aug 2014)C1425 Open in Stop Light Switch Circuit (from Aug 2014) →