C2174/74 Vehicle Speed Signal Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C2191/91 Vehicle Speed Signal Error (Test Mode DTC)
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.DTC C2191/91 is stored only during the signal check.
| DTC Code |
Detection Condition |
Trouble Area |
| C2174/74 |
All conditions below are met:
|
|
| C2191/91 |
Test mode procedure is performed. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
- It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
- When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
- HINT:
- When the speedometer needle is not moving, first troubleshoot the meter/gauge system (Click here).
| 1. READ VALUE USING DATA LIST (VEHICLE SPEED) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check that the values indicated on the GTS and on the combination meter assembly are the same.
Tire Pressure Monitor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on combination meter assembly
- OK:
- Vehicle speed indicated on the GTS indicates the actual speed.
|
|
||||
| OK | |
| 2. CHECK DTC OUTPUT |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch ON.
Perform a driving test.
Check for DTCs (Click here).
- HINT:
- The time required for DTC C2174 to be stored is 20 minutes.
Result Result
Proceed to
DTC C2174 is not output
A
DTC C2174 is output
B
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY) |
Disconnect the tire pressure warning ECU and receiver R41 connector.
Disconnect the combination meter assembly G6 connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R41-2 (SPD) - G6-32 (+S)
Always
Below 1 Ω
R41-2 (SPD) or G6-32 (+S) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU) |
Disconnect the skid control ECU (master cylinder solenoid) A6*1 or A7*2 connector.
- *1: for Vacuum Brake Booster
- *2: for Hydraulic Brake Booster
- *1: for Vacuum Brake Booster
Disconnect the combination meter assembly G6 connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for Vacuum Brake Booster Tester Connection
Condition
Specified Condition
A6-11 (SP1) - G6-33 (SI)
Always
Below 1 Ω
A6-11 (SP1) or G6-33 (SI) - Body ground
Always
10 kΩ or higher
for Hydraulic Brake Booster Tester Connection
Condition
Specified Condition
A7-12 (SP1) - G6-33 (SI)
Always
Below 1 Ω
A7-12 (SP1) or G6-33 (SI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK DTC OUTPUT |
Check for DTCs.
- HINT:
- for 1GR-FE (Click here).
- for 1KD-FTV (w/ DPF) (Click here).
- for 1KD-FTV (w/o DPF) (Click here).
- for 2TR-FE (Click here).
- for 1GR-FE (Click here).
Result Result
Proceed to
DTC P0500 is not output
A
DTC P0500 is output
B
|
|
||||
| A | |
| 6. REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER |
Replace the tire pressure warning ECU and receiver (Click here).
| NEXT | |
| 7. PERFORM REGISTRATION OF TRANSMITTER ID |
Perform registration (Click here).
| NEXT | |
| 8. PERFORM INITIALIZATION |
Perform initialization (Click here).
| NEXT | |
| 9. CHECK TEST MODE DTC (C2191/91) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.
Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).
Result Result
Proceed to
DTC C2191 is not cleared
A
DTC C2191 is cleared
B
|
|
||||
| A | ||
| ||
