2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Driver Side Door Entry Lock Function does not Operate

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If the driver side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter is normal. The malfunctioning part may be an entry lock sensor circuit (front door outside handle assembly [for driver side] → certification ECU).

WIRING DIAGRAM

B243940E03

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  6. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos*1
    Front RH side door lock position switch signal / UNLOCK or LOCK
    UNLOCK: Front RH side door unlocked
    LOCK: Front RH side door locked
    -
    FL Door Lock Pos*2
    Front LH side door lock position switch signal / UNLOCK or LOCK
    UNLOCK: Front LH side door unlocked
    LOCK: Front LH side door locked
    -
    1. *1: for RHD
    2. *2: for LHD

    OK:
    On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door Lock/Unlock Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)
  1. Using the intelligent tester, read the Data List (Click here).

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Trigger Switch
    Driver side door lock sensor / ON or OFF
    ON: Driver side door lock sensor touched
    OFF: Driver side door lock sensor not touched
    -

    OK:
    "ON" (lock sensor is touched) and "OFF" (lock sensor is not touched) appear on the screen.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU

4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the O1*1 or N1*2 handle connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O1-1 (TRG+) - G38-18 (TSW1)
    Always
    Below 1 Ω
    G38-18 (TSW1) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N1-1 (TRG+) - G38-18 (TSW1)
    Always
    Below 1 Ω
    G38-18 (TSW1) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (LOCK SENSOR)

  1. Measure the voltage according to the value(s) in the table below.B224125E22

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-18 (TSW1) - G38-15 (E)
    Engine switch off, all doors closed and lock sensor (for driver side) off → on
    Pulse generation → Below 2 V



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE) (Click here)
OK

REPLACE CERTIFICATION ECU


← Front Passenger Side Door Entry Lock and Unlock Functions do not Operate (from Aug 2014)Driver Side Door Entry Lock Function does not Operate (from Aug 2014) →