2013-2015 Land Cruiser Prado · Service Manual Steering

B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the amount that the steering column slides forward or backward and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

HINT:
The limit positions can be confirmed on the Data List screen of the intelligent tester.
DTC Code
Detection Condition
Trouble Area
B2611
The telescopic operation stops within the operation range while operating.
  1. Harness or connector
  2. Telescopic position sensor or telescopic motor
  3. Multiplex tilt and telescopic ECU


WIRING DIAGRAM

C215716E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCO OPERATION)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering column contracts and extends.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Telesco Operation
    Telescopic operation
    LONG/SHORT
    -
    Result 
    Result
    Proceed to
    The steering column does not contract/extend.
    A
    The steering column contracts/extends.
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

  1. C197979E13
    Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G116-2 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

  1. C197979E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK TELESCOPIC MOTOR
  1. Reconnect the G116 multiplex tilt and telescopic ECU connector.

  1. Disconnect the A telescopic motor connector.

  1. C205366E01
    Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

    OK:
    Measurement Condition
    Specified Condition
    12 V battery positive (+) lead → Terminal A-2 (TEM+)
    12 V battery negative (-) lead → Terminal A-6 (TEM-)
    The steering column contracts.
    12 V battery positive (+) lead → Terminal A-6 (TEM-)
    12 V battery negative (-) lead → Terminal A-2 (TEM+)
    The steering column extends.

    Text in Illustration 
    *a
    Rear view of wire harness connecter
    (to Multiplex Tilt and Telescopic ECU)



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

5. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
  1. Disconnect the G116 multiplex tilt and telescopic ECU connector.

  1. C197979E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G116-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
  1. Reconnect the G116 multiplex tilt and telescopic ECU connector.

  1. C197975E14
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (VCE) - A-5 (E2)
    Engine switch on (IG)
    8 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Multiplex Tilt and Telescopic ECU)



NG
Go to step 8
OK


7. CHECK TELESCOPIC POSITION SENSOR

  1. C197975E15
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-4 (TES) - A-5 (E2)
    Telescopic steering contracting or extending
    Pulse generation
    High: 8 to 14 V
    Low: Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Multiplex Tilt and Telescopic ECU)



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

8. CHECK STEERING COLUMN ASSEMBLY
  1. Disconnect the A multiplex tilt and telescopic ECU connector.

  1. C215717E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (VCE) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)


← B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction (Aug 2013 – Jul 2014)B2620 ECU Power Source Circuit Malfunction (Aug 2013 – Jul 2014) →