2013-2015 Land Cruiser Prado · Service Manual Steering

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering wheel (Click here).

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disable the auto tilt away function by changing the customize parameter (Click here).

    NOTICE:
    Record the current customize parameter setting (whether the auto tilt away function is enabled or disabled) in order to restore the current setting after finishing the operation.

    HINT:
    Performing the above operation causes the auto tilt away function to be disabled when the engine switch is turned off.

  1. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

  1. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT WHEEL LH

4. REMOVE STEERING WHEEL ASSEMBLY
(Click here)

5. REMOVE STEERING COLUMN LOWER COVER

  1. C215856
    Remove the 3 screws.

  1. Detach the 2 claws and remove the steering column lower cover.

    NOTICE:
    Do not damage the tilt and telescopic switch.


6. REMOVE STEERING COLUMN UPPER COVER

  1. C215846
    Detach the 4 clips.

  1. Detach the claw and remove the steering column upper cover.


7. REMOVE TILT AND TELESCOPIC SWITCH

  1. C215874E01
    Disconnect the connector.

  1. Detach the claw and pull out the tilt and telescopic switch.

    NOTICE:
    Pushing on the claw too hard will break the claw.


8. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the combination switch with spiral cable.

  1. C215847
    Use pliers to hold the clamp and raise the claw with a screwdriver. Then remove the combination switch switch assembly with spiral cable sub-assembly from the steering column assembly.


9. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
(Click here)

10. REMOVE NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
(Click here)

11. REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)
  1. Detach the claws and remove the wire harness protector and wire harness.

  1. C215861E01
    Put matchmarks on the steering actuator and steering column.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt.

  1. C172653
    Remove the 4 nuts, steering column and steering shaft stopper.


12. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

  1. A223334
    w/ KDSS:
    Remove the 7 clips and fender apron seal.

  1. A223333
    w/o KDSS:
    Remove the 5 clips and fender apron seal.


13. DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C215850E01
    Put matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt, and then pull out the intermediate shaft toward the inside of the vehicle.


14. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  1. C215852
    Remove the 4 bolts and steering column hole cover from the vehicle.


15. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C215851E01
    Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.

← REMOVAL (Aug 2013 – Jul 2014)DISASSEMBLY (from Aug 2013) →