Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- If the auto up/down function does not operate, the cause may be one or more of the following:
- The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
- The power window regulator switch has a malfunction.
- The Hall IC in the power window regulator motor has a malfunction.
- There is an open or short in the wiring between the power window regulator switch and power window regulator motor.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC B2311 is output
B
DTC B2312 is output
C
DTC B2313 is output
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH) |
Check that the manual up/down function using the front power window regulator switch can operate the front power window (Click here).
- OK:
- Front passenger side door power window moves.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH) |
Use the Data List to check if the front power window regulator is functioning properly (Click here).
P-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Door P/W Auto SW
Front passenger side power window auto up/down signal / ON or OFF
ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Remove the power window regulator switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
8 (AUTO) - 1 (GND)
Auto up/down operation
Below 1 Ω
8 (AUTO) - 1 (GND)
Not operated
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR RH AND BODY GROUND) |
- *1: for LHD
- *2: for RHD
Disconnect the J1*1 or K10*2 power window regulator switch connector.
Disconnect the J7*1 or K7*2 power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD: Tester Connection
Condition
Specified Condition
J1-8 (AUTO) - J7-4 (AUTO)
Always
Below 1 Ω
J1-1 (GND) - Body ground
Always
Below 1 Ω
J1-8 (AUTO) - Body ground
Always
10 kΩ or higher
for RHD: Tester Connection
Condition
Specified Condition
K10-8 (AUTO) - K7-4 (AUTO)
Always
Below 1 Ω
K10-1 (GND) - Body ground
Always
Below 1 Ω
K10-8 (AUTO) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
