2013-2015 Land Cruiser Prado · Service Manual Brake

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation is not possible.
  5. The voltage at terminal IG1 is high.

WIRING DIAGRAM

C215176E01

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (for LHD without Entry and Start System: Click here, for RHD without Entry and Start System: Click here).

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    for LHD without Entry and Start System
    B
    DTC output
    for RHD without Entry and Start System
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. CHECK TERMINAL VOLTAGE (IG1)
  1. Disconnect the A6 skid control ECU connector.

  1. C199357E08
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
  1. Disconnect the A6 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


5. READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch/ ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 9
OK


6. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the A44 brake fluid level warning switch connector.

  1. C219276E01
    Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch off (Float up)
    10 kΩ or higher
    Switch on (Float down)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch)

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the G6 combination meter connector.

  1. Disconnect the A44 brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-31 (SW) - A44-1
    Always
    Below 1 Ω
    G6-31 (SW) - Body ground
    Always
    10 kΩ or higher
    A44-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light/ ON or OFF
    OFF
    -

  1. When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe combination meter
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Does not change between ON and OFF
    A
    Changes between ON and OFF
    B
    OFF
    Does not change between ON and OFF
    A
    Changes between ON and OFF
    B



B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

9. INSPECT PARKING BRAKE SWITCH
  1. Turn the ignition switch off.

  1. Disconnect the G77 parking brake switch connector.

  1. C215408E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch on
    (Switch pin free)
    Below 1 Ω
    Parking brake switch off
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Parking Brake Switch)



NG
REPLACE PARKING BRAKE SWITCH (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK))
  1. Disconnect the 2D main body ECU (driver side junction block assembly) connector.

  1. Disconnect the G77 parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-23 (PKB) - G77-1
    Always
    Below 1 Ω
    2D-23 (PKB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)


← Brake Warning Light Remains ON (Aug 2013 – Jul 2014)Brake Warning Light does not Come ON (Aug 2013 – Jul 2014) →