2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine from the vehicle (Click here).


2. REMOVE IGNITION COIL ASSEMBLY

  1. A222689
    Disconnect the 4 ignition coil connectors.

  1. A222690
    Remove the 4 bolts and 4 ignition coils.


3. REMOVE GENERATOR ASSEMBLY

  1. A223928
    Remove the terminal cap.

  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. A223930
    Remove the 2 bolts and generator.


4. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. G035081E03
    Remove the 3 bolts and belt tensioner.


5. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A099203
    Remove the 5 bolts and No. 1 compressor mounting bracket.


6. REMOVE WATER INLET

  1. A222348
    Remove the bolt, 2 nuts, water inlet and gasket.


7. REMOVE THERMOSTAT

  1. A223318
    Remove the thermostat from the timing chain cover.


8. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

  1. G037698E01
    Disconnect the water by-pass hose.

  1. Disconnect the No. 2 water by-pass hose.

  1. Disconnect the throttle position sensor and throttle control motor connector.

  1. G037699E01
    for Type A:
    Remove the 2 bolts, 2 nuts and throttle body with motor.

  1. for Type B:
    Remove the 4 bolts and throttle body with motor.

  1. G037700E01
    Remove the gasket from the intake manifold.


9. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold (Click here).


10. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A222362
    Remove the bolt, idler pulley and spacer.


11. REMOVE CAMSHAFT POSITION SENSOR

G037910E01
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.


12. REMOVE CRANKSHAFT POSITION SENSOR

  1. A222453
    Disconnect the crankshaft position sensor connector and detach the wire harness clamp.

  1. G037914E02
    Remove the bolt and crankshaft position sensor.


13. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A222349
    Remove the 2 nuts, bolt, water by-pass pipe and gasket.


14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.


15. REMOVE CRANKSHAFT PULLEY

  1. A101288E02
    Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  
    Text in Illustration 
    *a
    Loosen
    *b
    Hold

  1. A101289E02
    Using SST and the pulley bolt, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)
    Text in Illustration 
    *a
    Loosen
    *b
    Hold

    HINT:
    Apply lubricant to the threads and end of SST.


16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A224903
    Remove the drain plug and gasket.

  1. Remove the 18 bolts and 2 nuts.

  1. A101293
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


17. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A265913
    Remove the bolt, 2 nuts, oil strainer and gasket.


18. REMOVE OIL PAN SUB-ASSEMBLY

  1. A273964E01
    Remove the 16 bolts and 2 nuts.

  1. A101296E02
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. A101297E01
    Remove the O-ring.


19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A101298E01
    Remove the 19 bolts and 2 nuts shown in the illustration.

  1. A101299E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A222350E02
    Remove the 3 O-rings.


20. REMOVE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, water pump and gasket.


21. REMOVE TIMING CHAIN COVER OIL SEAL

  1. A101302E02
    Place the timing chain cover on wooden blocks.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

  1. Using a screwdriver pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →