REMOVAL
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1.
REMOVE ENGINE ASSEMBLY |
 |
Remove the engine from the vehicle (Click here).
| 2.
REMOVE IGNITION COIL ASSEMBLY
|
 |
- Disconnect the 4 ignition coil connectors.
- Remove the 4 bolts and 4 ignition coils.
| 3.
REMOVE GENERATOR ASSEMBLY
|
 |
- Remove the terminal cap.
Remove the nut and generator wire.
Disconnect the generator connector.
- Remove the 2 bolts and generator.
| 4.
REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
 |
- Remove the 3 bolts and belt tensioner.
| 5.
REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
|
 |
- Remove the 5 bolts and No. 1 compressor mounting bracket.
| 6.
REMOVE WATER INLET |
 |
- Remove the bolt, 2 nuts, water inlet and gasket.
| 7.
REMOVE THERMOSTAT
|
 |
- Remove the thermostat from the timing chain cover.
| 8.
REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY
|
 |
- Disconnect the water by-pass hose.
Disconnect the No. 2 water by-pass hose.
Disconnect the throttle position sensor and throttle control motor connector.
- for Type A:
Remove the 2 bolts, 2 nuts and throttle body with motor.
for Type B:
Remove the 4 bolts and throttle body with motor.
- Remove the gasket from the intake manifold.
| 9.
REMOVE INTAKE MANIFOLD |
 |
Remove the intake manifold (Click here).
| 10.
REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
 |
- Remove the bolt, idler pulley and spacer.
| 11.
REMOVE CAMSHAFT POSITION SENSOR
|
 |
Disconnect the camshaft position sensor connector.
Remove the bolt and camshaft position sensor.
| 12.
REMOVE CRANKSHAFT POSITION SENSOR
|
 |
- Disconnect the crankshaft position sensor connector and detach the wire harness clamp.
- Remove the bolt and crankshaft position sensor.
| 13.
REMOVE NO. 1 WATER BY-PASS PIPE |
 |
- Remove the 2 nuts, bolt, water by-pass pipe and gasket.
| 14.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
 |
- Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.
| 15.
REMOVE CRANKSHAFT PULLEY
|
 |
- Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.
- SST
- 09213-54015
(91651-60855)
09330-00021
Text in Illustration
*a
|
Loosen
|
*b
|
Hold
|
- Using SST and the pulley bolt, remove the crankshaft pulley.
- SST
- 09950-50013
(09951-05010, 09952-05010, 09953-05010, 09954-05021)
Text in Illustration
*a
|
Loosen
|
*b
|
Hold
|
- HINT:
- Apply lubricant to the threads and end of SST.
| 16.
REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
 |
- Remove the drain plug and gasket.
Remove the 18 bolts and 2 nuts.
- Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.
- NOTICE:
- Be careful not to damage the contact surfaces of the oil pans.
| 17.
REMOVE OIL STRAINER SUB-ASSEMBLY |
 |
- Remove the bolt, 2 nuts, oil strainer and gasket.
| 18.
REMOVE OIL PAN SUB-ASSEMBLY |
 |
- Remove the 16 bolts and 2 nuts.
- Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
Text in Illustration
*1
|
Protective Tape
|
- HINT:
- Tape the screwdriver tip before use.
- NOTICE:
- Be careful not to damage the contact surfaces of the cylinder block and oil pan.
- Remove the O-ring.
| 19.
REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
 |
- Remove the 19 bolts and 2 nuts shown in the illustration.
- Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
Text in Illustration
*1
|
Protective Tape
|
- HINT:
- Tape the screwdriver tip before use.
- NOTICE:
- Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.
- Remove the 3 O-rings.
| 20.
REMOVE WATER PUMP ASSEMBLY |
 |
- Remove the 8 bolts, water pump and gasket.
| 21.
REMOVE TIMING CHAIN COVER OIL SEAL |
 |
- Place the timing chain cover on wooden blocks.
Text in Illustration
*1
|
Protective Tape
|
*2
|
Wooden Block
|
Using a screwdriver pry out the oil seal.
- HINT:
- Tape the screwdriver tip before use.