2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. A222363
    Remove the 8 bolts and hood.

    NOTICE:
    If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.


4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
  1. Remove the cowl top ventilator louver (Click here).


5. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


6. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A224743
    Remove the 4 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.


7. REMOVE TRANSMISSION UNDER COVER
  1. Remove the 2 bolts and transmission under cover.


8. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


9. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


10. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A223311E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Cylinder Block Drain Cock Plug
*4
Radiator Drain Cock Plug

  1. G038197E02
    Install a vinyl hose to the radiator side.
    Text in Illustration 
    *1
    Vinyl Hose

  1. G038198E02
    Install a vinyl hose to the engine side.
    Text in Illustration 
    *1
    Vinyl Hose

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


11. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and gasket, and drain the oil into a container.


12. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A218394
    Detach the 3 clamps and disconnect the mass air flow meter connector.

  1. Remove the bolt, detach the clamp and disconnect the ground wire.

  1. A223921
    Detach the 4 clamps.

  1. Loosen the hose clamp and remove the air cleaner cap.


14. REMOVE AIR CLEANER CASE

  1. A218395
    Remove the air cleaner filter element.

  1. Remove the 3 bolts and air cleaner case.


15. REMOVE INTAKE AIR CONNECTOR

  1. A273728
    w/ Manifold absolute pressure sensor:

    1. Disconnect the air pressure sensor connector.

    2. Detach the 2 clamps.

    3. Disconnect the vacuum hose.

  1. A224325
    Disconnect the No. 2 ventilation hose.

  1. Detach the wire harness clamp.

  1. G037696E01
    Disconnect the vacuum hose.

  1. A224324
    Loosen the hose clamp.

  1. Remove the 3 bolts and intake air connector.


16. REMOVE NO. 1 AIR INJECTION SYSTEM HOSE

  1. A218385
    Remove the hose clamp.

    NOTICE:
    Do not reuse the hose clamp.

  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the air injection system hose.


17. REMOVE RADIATOR RESERVOIR

  1. A223323
    Disconnect the reservoir hose from the radiator.

  1. Remove the 3 bolts and radiator reservoir.


18. REMOVE NO. 1 RADIATOR HOSE
  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the radiator hose.


19. REMOVE NO. 2 RADIATOR HOSE
  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the radiator hose.


20. REMOVE FAN SHROUD

  1. A223324
    Detach the claw to open the flexible hose clamp.

  1. A223325
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A223326
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.


21. REMOVE NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

C213699E01
  1. Disconnect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from the No. 2 oil cooler tube.

  1. Disconnect the 2 hoses from the oil cooler inlet tube and No. 1 oil cooler outlet tube and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.


22. REMOVE FUEL HOSE

  1. A222373
    Detach the 2 clamps.

  1. Remove the fuel hose (Click here).


23. REMOVE NO. 2 FUEL HOSE

  1. A222374
    Disconnect the fuel hose from the clamp.

  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the fuel hose.


24. DISCONNECT PURGE LINE HOSE

  1. A222378
    Disconnect the purge line hose from the vacuum switching valve.


25. DISCONNECT UNION TO CHECK VALVE HOSE

  1. A264501
    Using needle-nose pliers, grip the claws of the clamp and slide the clamp to disconnect the check valve hose.


26. DISCONNECT HEATER HOSE

  1. A218386
    Disconnect the 2 heater water hoses.


27. DISCONNECT VANE PUMP ASSEMBLY

  1. A218388
    Remove the bolt and disconnect the pressure feed tube.

  1. A218387
    Disconnect the 2 connectors.

  1. Remove the 2 bolts and disconnect the vane pump.

    HINT:
    It is not necessary to completely remove the vane pump. With the hoses connected to the vane pump, hang the vane pump on the vehicle body with a rope.


28. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A218390
    Remove the bolt and disconnect the suction hose from the engine.

  1. A218389
    Disconnect the connector.

  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


29. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

  1. C214928
    Remove the 5 clips and front No. 1 fender apron to frame seal.


30. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

C213693
  1. Remove the 5 clips and front fender apron to frame seal.


31. DISCONNECT ENGINE WIRE

  1. A222379
    Detach the 3 clamps and disconnect the engine wire from the vehicle RH side.

  1. Disconnect the ECM connector.

    1. Remove the glove compartment door (Click here).

    2. A264497
      Detach the clamp and disconnect the 9 connectors.

    3. A268576
      Detach the clamp.

    4. A264503
      Detach the grommet from the wire harness support.

    5. A264504
      Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.

  1. A218402
    Disconnect the connector and detach the clamp.

  1. Remove the nut from the engine room No. 1 relay block.

  1. Detach the 2 clamps and disconnect the wire harness from the engine room No. 1 relay block.

  1. A218399
    Detach the 2 clamps.

  1. Remove the bolt and disconnect the ground wire.

  1. A222394
    Remove the bolt and bracket from the engine mounting bracket LH.


32. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector and detach the wire harness clamp.

  1. Disconnect the heated oxygen sensor connector and detach the wire harness clamp.

  1. Remove the 4 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support to remove the front exhaust pipe assembly.

  1. Remove the 2 gaskets.


33. REMOVE MANIFOLD STAY

  1. C214941
    Remove the 3 bolts and manifold stay.


34. REMOVE PROPELLER SHAFT ASSEMBLY

  1. C219704E01
    Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *A
    for 3 Door
    *B
    for 5 Door
    *a
    Matchmark

  1. Remove the 4 nuts and 4 washers.

  1. C219705E01
    Place matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *A
    for 3 Door
    *B
    for 5 Door
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. Remove the propeller shaft.


35. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

  1. C098708E07
    Place matchmarks on the propeller shaft flange and differential.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.

  1. C098709E10
    Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.


36. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)
  1. Remove the flywheel housing dust seal.

  1. C118033
    Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.


37. REMOVE STARTER ASSEMBLY
  1. for 1.4 kW Type:
    Remove the starter assembly (Click here).

  1. for 2.0 kW Type:
    Remove the starter assembly (Click here).


38. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
  1. Remove the automatic transmission assembly (Click here).


39. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
  1. Remove the manual transmission assembly (Click here).


40. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the engine mounting insulator is necessary.

  1. for Automatic Transmission:

    1. A222390
      Remove the 4 bolts of the rear engine mounting insulator.

    2. A222391
      Remove the bolt and rear engine mounting heat insulator.

    3. Remove the 4 bolts and engine mounting insulator from the transmission.

  1. for Manual Transmission:

    1. C215702
      Remove the 4 bolts of the rear engine mounting insulator.

    2. A222421
      Remove the bolt and rear engine mounting heat insulator.

    3. Remove the 4 bolts and engine mounting insulator from the transmission.


41. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. G038108E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A222355
    Remove the 10 bolts, rear drive plate spacer, drive plate and front drive plate spacer.


42. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C215531E01
    Place matchmarks on the clutch cover and flywheel.
    Text in Illustration 
    *a
    Matchmark

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


43. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, the pressure plate and the surface of the flywheel away from oil and foreign matter.


44. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. G038108E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A222354
    Remove the 10 bolts and flywheel.


45. REMOVE REAR END PLATE
  1. Detach the flywheel housing dust seal.

  1. Remove the 2 bolts and rear end plate.


46. INSTALL NO. 1 ENGINE HANGER

  1. A087220E01
    Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *a
    LH Side
    *b
    RH Side

    HINT:
    No. 1 Engine Hanger
    12281-75040
    Bolt
    91552-A1020


47. REMOVE ENGINE ASSEMBLY
  1. Attach an engine sling device and hang the engine with a chain block.

    NOTICE:
    Pay attention to the angle of the sling device as the engine assembly or engine hanger may be damaged or deformed if the angle is incorrect.

  1. A218401E01
    Remove the 4 engine mounting insulator bolts and nuts.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side

  1. Lift the engine out from the vehicle slowly and carefully.

    NOTICE:
    Make sure the engine is clear of all wiring, hoses and cables.


48. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

  1. Remove the 2 bolts and 2 engine hangers.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →