2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
3.
REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 8 bolts and hood.
NOTICE:
If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.
4.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Remove the cowl top ventilator louver (Click here).
5.
REMOVE FRONT BUMPER COVER LOWER
Remove the clip, 5 bolts and front bumper cover lower.
6.
REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
7.
REMOVE TRANSMISSION UNDER COVER
Remove the 2 bolts and transmission under cover.
8.
REMOVE REAR ENGINE UNDER COVER ASSEMBLY
Remove the 4 bolts and rear engine under cover.
9.
REMOVE UPPER RADIATOR SUPPORT SEAL
Remove the 13 clips and upper radiator support seal.
10.
DRAIN ENGINE COOLANT
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Text in Illustration
*1
Reservoir Cap
*2
Radiator Cap
*3
Cylinder Block Drain Cock Plug
*4
Radiator Drain Cock Plug
Install a vinyl hose to the radiator side.
Text in Illustration
*1
Vinyl Hose
Install a vinyl hose to the engine side.
Text in Illustration
*1
Vinyl Hose
Loosen the radiator drain cock plug.
Remove the radiator cap and drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Loosen the cylinder block drain cock plug and drain the coolant from the engine.
11.
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil drain plug and gasket, and drain the oil into a container.
Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the fuel hose.
24.
DISCONNECT PURGE LINE HOSE
Disconnect the purge line hose from the vacuum switching valve.
25.
DISCONNECT UNION TO CHECK VALVE HOSE
Using needle-nose pliers, grip the claws of the clamp and slide the clamp to disconnect the check valve hose.
26.
DISCONNECT HEATER HOSE
Disconnect the 2 heater water hoses.
27.
DISCONNECT VANE PUMP ASSEMBLY
Remove the bolt and disconnect the pressure feed tube.
Disconnect the 2 connectors.
Remove the 2 bolts and disconnect the vane pump.
HINT:
It is not necessary to completely remove the vane pump. With the hoses connected to the vane pump, hang the vane pump on the vehicle body with a rope.
28.
DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the bolt and disconnect the suction hose from the engine.
Disconnect the connector.
Remove the 4 bolts and disconnect the cooler compressor.
HINT:
It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
29.
REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
Remove the 5 clips and front No. 1 fender apron to frame seal.
30.
REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
Remove the 5 clips and front fender apron to frame seal.
31.
DISCONNECT ENGINE WIRE
Detach the 3 clamps and disconnect the engine wire from the vehicle RH side.