2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1860/64 Short in Driver Side Knee Airbag Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The driver side knee squib circuit consists of the center airbag sensor and lower No. 1 instrument panel airbag.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee squib circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1860/64
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the driver side knee squib circuit during the primary check.
  2. A driver side knee squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Lower No. 1 instrument panel airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1861/64
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the driver side knee squib circuit for 2 seconds.
  2. A driver side knee squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Lower No. 1 instrument panel airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1862/64
One of the following conditions is met:
  1. The airbag sensor center detects a short circuit to ground signal in the driver side knee squib circuit for 0.5 seconds.
  2. A driver side knee squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Lower No. 1 instrument panel airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1863/64
One of the following conditions is met:
  1. The airbag sensor center detects a short circuit to B+ signal in the driver side knee squib circuit for 0.5 seconds.
  2. A driver side knee squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Lower No. 1 instrument panel airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C146265E21

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG (DRIVER SIDE KNEE SQUIB)

  1. C214268E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the lower No. 1 instrument panel airbag.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the lower No. 1 instrument panel airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862 or B1863 is not output.

    HINT:
    Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Knee Squib
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Driver Side Knee Squib)



NG
Go to step 2
OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. C207498E01
    Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Driver Side Knee Squib
    *2
    Center Airbag Sensor



NG
REPLACE INSTRUMENT PANEL WIRE
OK


3. CHECK INSTRUMENT PANEL WIRE (LOWER NO. 1 INSTRUMENT PANEL AIRBAG - CENTER AIRBAG SENSOR)

  1. C214269E02
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G32-1 (DK+) - Body ground
    Ignition switch ON
    Below 1 V
    G32-2 (DK-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G32-1 (DK+) - G32-2 (DK-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G32-1 (DK+) - G32-2 (DK-)
    Always
    1 MΩ or higher
    G32-1 (DK+) - Body ground
    Always
    1 MΩ or higher
    G32-2 (DK-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Driver Side Knee Squib
*2
Instrument Panel Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Driver Side Knee Squib)


NG
REPLACE INSTRUMENT PANEL WIRE
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C207499E02
    Connect the connectors to the lower No. 1 instrument panel airbag and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862 or B1863 is not output.

    HINT:
    Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Knee Squib
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1860/64 Short in Driver Side Knee Airbag Squib Circuit (+ B1861/64, B1862/64, B1863/64) (Aug 2013 – Jul 2014)B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (Aug 2013 – Jul 2014) →