2013-2015 Land Cruiser Prado · Service Manual Brake

C1437 Lost Communication with ECM

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU receives signals from the ECM via the CAN communication system.
DTC Code
DTC Detection Condition
Trouble Area
C1437
When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more.
  1. Engine control system
  2. CAN communication system
  3. Master cylinder solenoid (Skid control ECU)

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    EFI Communication Open
    EFI communication open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC C1437 is not output
    A
    DTC C1437 is output (for 1GR-FE)
    B
    DTC C1437 is output (for 1KD-FTV)
    C
    CAN communication system DTC is output (for LHD)
    D
    CAN communication system DTC is output (for RHD)
    E

    HINT:
    For 1KD-FTV, refer to the following sections.
    1. w/ DPF: Click here
    2. w/o DPF: Click here



B
GO TO ENGINE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO ENGINE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - ECM)
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and ECM (Click here).

  1. Check that there is no momentary interruption.


NEXT


4. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC C1437 is not output
    A
    DTC C1437 is output (for LHD)
    B
    DTC C1437 is output (for RHD)
    C
    CAN communication system DTC is output (for LHD)
    D
    CAN communication system DTC is output (for RHD)
    E



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

END


← C1437 Lost Communication with ECM (Aug 2013 – Jul 2014)C1439 Steering Angle Sensor Initialization Incomplete (+ C1445) (Aug 2013 – Jul 2014) →