Daytime Running Light Relay Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The main body ECU controls the daytime running lights.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DAYTIME RUNNING LIGHT) |
 |
Using the intelligent tester, perform the Active Test (Click here).
Main Body
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
Daytime Running Light
|
Daytime running light relay
|
ON/OFF
|
-
|
- OK:
- Daytime running Lights illuminate.
|
NG |
 |
|
|
|
| OK |
|
 |
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
|
|
| 2. INSPECT DAYTIME RUNNING LIGHT RELAY (DRL) |
 |
- Remove the daytime running light relay from the engine room No. 5 relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage not applied between terminals 1 and 2
|
10 kΩ or higher
|
3 - 5
|
Battery voltage applied between terminals 1 and 2
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE DAYTIME RUNNING LIGHT RELAY RELAY (DRL) |
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY [DRL] - BATTERY) |
 |
- Remove the daytime running light relay from the engine room No. 5 relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
Daytime running light relay terminal 5 - Body ground
|
Always
|
11 to 14 V
|
Daytime running light relay terminal 2 - Body ground
|
Text in Illustration
*a
|
Front view of wire harness connector (to Daytime Running Light Relay [DRL])
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY [DRL] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY) |
 |
Remove the daytime running light relay from the engine room No. 5 relay block.
Disconnect the 2F driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Daytime running light relay terminal 1 - 2F-24
|
Always
|
Below 1 Ω
|
2F-24 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 5. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
 |
- Remove the driver side junction block assembly (Click here).
Remove the main body ECU from the driver side junction block assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-22 (DRL) - 2F-24
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
|
|
|
| OK |
|
 |
|
| PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
|
|