2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes current to flow to the EFI relay coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A227838E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK ECM (+B VOLTAGE)
A062416E96
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G61-12 (+B) - C101-14 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A062420E13
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C101-14 (E1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (IGSW VOLTAGE)
A062416E97
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G61-14 (IGSW) - C101-14 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 7
OK


4. CHECK ECM (MREL VOLTAGE)
A062416E98
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G61-3 (MREL) - C101-14 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK


5. CHECK NO. 1 INTEGRATION RELAY (EFI)
G039047E21
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1B-4 - Body ground
    Ignition switch ON
    10 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Integration Relay)

  1. Reconnect the No. 1 integration relay (EFI) connector.



NG
REPLACE NO. 1 INTEGRATION RELAY (EFI)
OK


6. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI) - ECM AND BODY GROUND)
  1. Disconnect the No. 1 integration relay (EFI) connector from the engine room junction block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1B-2 - G61-3 (MREL)
    Always
    Below 1 Ω
    1B-4 - G61-12 (+B)
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1B-2 or G61-3 (MREL) - Body ground
    Always
    10 kΩ or higher
    1B-4 or G61-12 (+B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 1 integration relay (EFI) connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TERMINAL +B OF ECM - BATTERY)

7. INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)


← ECM Power Source Circuit (Aug 2013 – Jul 2014)Starter Signal Circuit (Aug 2013 – Jul 2014) →