B2417 Headlight Beam Level Control Motor LH Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- B2418 Headlight Beam Level Control Motor RH Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The headlight leveling motor receives a signal from the headlight swivel ECU to operate. The headlight swivel ECU receives a signal indicating the operating conditions of the headlight leveling motor.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2417 |
|
|
| B2418 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
|
|
||||
| OK | ||
| ||
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LEVELING MOTOR) |
Using the intelligent tester, perform the Active Test (Click here).
AFS Tester Display
Test Part
Control Range
Diagnostic Note
Drive The Leveling Motor UP*
Leveling motor upward operation
ON/OFF
ON: Move up
OFF: Stop
Drive The Leveling Motor DOWN*
Leveling motor downward operation
ON/OFF
ON: Move down
OFF: Stop
- *: Perform the Active Test with the engine running and the vehicle stopped.
- OK:
- Headlight leveling motors operate normally.
- *: Perform the Active Test with the engine running and the vehicle stopped.
|
|
||||
| OK | |
| 3. CHECK HEADLIGHT LEVELING MOTOR (OPERATION) |
for Halogen Headlight
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
for LED Headlight
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
|
|
||||
| OK | ||
| ||
| 4. READ VALUE USING INTELLIGENT TESTER (HEADLIGHT SWIVEL ECU) |
Using the intelligent tester, read the Data List (Click here).
AFS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
+B
IG power supply voltage value / 0 to 19.75 V
11 to 14 V
-
- OK:
- Power supply voltage is 11 to 14 V.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BODY GROUND) |
Disconnect the A58 headlight swivel ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A58-22 (E1) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Headlight Swivel ECU Assembly)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT) |
Disconnect the A58 headlight swivel ECU connector.
Disconnect the A30*1 or A31*2 headlight connector.
- *1: for LH
- *2: for RH
- *1: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
A58-3 (LHT) - A30-6 (LHB1)
Always
Below 1 Ω
A58-27 (LH-) - A30-8 (LHE)
Always
Below 1 Ω
A58-30 (LH+) - A30-7 (LHM+)
Always
Below 1 Ω
A58-3 (LHT) - Body ground
Always
10 kΩ or higher
A58-27 (LH-) - Body ground
Always
10 kΩ or higher
A58-30 (LH+) - Body ground
Always
10 kΩ or higher
- for RH:
Tester Connection
Condition
Specified Condition
A58-4 (RHT) - A31-6 (RHB1)
Always
Below 1 Ω
A58-28 (RH-) - A31-8 (RHE)
Always
Below 1 Ω
A58-11 (RH+) - A31-7 (RHM+)
Always
Below 1 Ω
A58-4 (RHT) - Body ground
Always
10 kΩ or higher
A58-28 (RH-) - Body ground
Always
10 kΩ or higher
A58-11 (RH+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT HEADLIGHT UNIT |
for Halogen Headlight
Remove the headlight unit (Click here).
for LED Headlight
Remove the headlight unit (Click here).
Disconnect the headlight leveling motor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
6 (LHB1) - 1 (LHB1)
Always
Below 1 Ω
7 (LHM+) - 2 (LHM+)
Always
Below 1 Ω
8 (LHE) - 3 (LHE)
Always
Below 1 Ω
- for RH:
Tester Connection
Condition
Specified Condition
6 (RHB1) - 1 (RHB1)
Always
Below 1 Ω
7 (RHM+) - 2 (RHM+)
Always
Below 1 Ω
8 (RHE) - 3 (RHE)
Always
Below 1 Ω
Result Result
Proceed to
OK
A
NG (Halogen Headlight)
B
NG (LED Headlight)
C
Text in Illustration *A
for LH
*B
for RH
|
|
||||
|
|
||||
| A | |
| 8. CHECK HEADLIGHT LEVELING MOTOR (OPERATION) |
for Halogen Headlight
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
for LED Headlight
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
| Result |
Proceed to |
| OK (Halogen Headlight) |
A |
| OK (LED Headlight) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | ||
| ||
