2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE CRANKSHAFT POSITION SENSOR

  1. A223429
    Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and crankshaft position sensor.


2. REMOVE CAMSHAFT TIMING PULLEY

  1. A057443E05
    Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.
    Text in Illustration 
    V100135
    Turn
    *1
    Timing Mark
    *2
    Protrusion

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

  1. A224023E01
    Using SST, loosen the pulley bolt.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. A224024E01
    Using SST, separate the timing pulley from the camshaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. Remove the pulley bolt and timing pulley.

  1. Remove the timing pulley woodruff key.


3. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts and timing belt cover.


4. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove the 9 bolts, nut, cylinder head cover and gasket.


5. REMOVE CAMSHAFT OIL SEAL RETAINER
  1. Remove the 4 bolts, retainer and gasket.


6. REMOVE CAMSHAFT OIL SEAL

  1. A057634E01
    Using a screwdriver and hammer, tap out the oil seal.


7. REMOVE CAMSHAFT

  1. A057786E03
    Turn the camshaft with a wrench so that the key groove faces upward.
    Text in Illustration 
    *1
    Upward
    *2
    Key Groove

  1. A057787E04
    Uniformly loosen and remove the 10 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. Remove the 5 bearing caps and camshaft.

    HINT:
    Arrange the bearing caps in the correct order.


8. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A057446E02
    Uniformly loosen and remove the 18 cylinder head bolts in several steps in the sequence shown.

    NOTICE:
    Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Lift the cylinder head from the dowels on the cylinder block to remove it, and place the cylinder head on wooden blocks on a workbench.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and block with a screwdriver.


9. REMOVE CYLINDER HEAD GASKET

10. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the bolt, No. 2 timing belt idler and spacer.


11. REMOVE WATER PUMP ASSEMBLY

  1. A218416
    Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.


12. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the 2 bolts (A and B).

  1. A056838E06
    Loosen the bolt (C), and remove the No. 1 timing belt idler.


13. REMOVE CRANKSHAFT TIMING PULLEY

  1. A056898E02
    Using a screwdriver, remove the crankshaft timing pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05010)

    HINT:
    If the timing pulley cannot be removed by using a screwdriver, remove it with SST.


14. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 16 bolts and 2 nuts.

  1. A057637E04
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut off the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use an oil pan seal cutter for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


15. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.


16. REMOVE TIMING BELT CASE SUB-ASSEMBLY

  1. A056912E01
    Remove the 5 bolts, timing belt case and gasket.


17. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A183537
    Using a screwdriver, pry out the oil seal.

    NOTICE:
    Tape the screwdriver tip before use.


18. REMOVE REAR CRANKSHAFT OIL SEAL RETAINER
  1. Remove the 4 bolts, oil seal retainer and gasket.


19. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A057266
    Using a screwdriver and hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

← REMOVAL (from Aug 2013)INSPECTION (from Aug 2013) →