P0418 Secondary Air Injection System Control "A" Circuit
Diagnostic trouble codes · Vehicles built from Aug 2013
DESCRIPTION
Refer to DTC P0412 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0418 |
|
|
|
|
MONITOR DESCRIPTION
This DTC indicates an open or short circuit in the circuit containing the air pump assembly of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, emission control valve set and itself and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump assembly, an emission control valve set or the air injection control driver, it illuminates the MIL and stores a DTC.WIRING DIAGRAM
Refer to DTC P0412 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the system check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the system check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
| 1. CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR INJECTION CONTROL DRIVER, AIR INJECTION CONTROL DRIVER - BATTERY) |
Disconnect the air pump assembly connector.
Disconnect the air injection control driver connector.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A18-2 - A17-2 (VP)
Always
Below 1 Ω
A18-4 - Body ground
Always
Below 1 Ω
A17-1 (BATT) - Battery positive terminal
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A18-2 or A17-2 (VP) - Body ground
Always
10 kΩ or higher
Reconnect the air pump assembly connector.
Reconnect the air injection control driver connector.
Reconnect the cable to the positive (+) battery terminal.
|
|
||||
| OK | |
| 2. INSPECT AIR PUMP ASSEMBLY |
Inspect the air pump assembly (Click here).
|
|
||||
| OK | ||
| ||
| 3. REPLACE AIR PUMP ASSEMBLY |
Replace the air pump assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
Start the engine after the intelligent tester initialization is finished.
Perform the system check operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
- OK:
- No pending DTC is output.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
|
|
||||
| OK | ||
| ||
