2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Engine Coolant Temperature Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

In this circuit, the meter CPU receives engine coolant temperature signals from the ECM. The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E204135E01
E204136E01

INSPECTION PROCEDURE

HINT:
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI System or ECD System.
  1. for 1GR-FE: (Click here)
  2. for 2TR-FE: (Click here)
  3. for 1KD-FTV (w/ DPF): (Click here)
  4. for 1KD-FTV (w/o DPF): (Click here)
  5. for 5L-E: (Click here)


1. CHECK ENGINE
  1. Check the engine type.

    Engine type 
    Engine type
    Proceed to
    not 5L-E
    A
    5L-E
    B



B
Go to step 5
A


2. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output.

    1. for LHD with Entry and Start System (Click here).

    2. for LHD without Entry and Start System (Click here).

    3. for RHD with Entry and Start System (Click here).

    4. for RHD without Entry and Start System (Click here).

      Result 
      Result
      Proceed to
      CAN communication DTC is not output.
      A
      CAN communication DTC is output. (for LHD with Entry and Start System)
      B
      CAN communication DTC is output. (for LHD without Entry and Start System)
      C
      CAN communication DTC is output. (for RHD with Entry and Start System)
      D
      CAN communication DTC is output. (for RHD without Entry and Start System)
      E



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/0 to 127.5°C (0 to 261.5°F)
    After warming up: 80 to 95°C (176 to 203°F)
    1. If -40°C (-40°F): Sensor circuit open
    2. If 140°C (284°F) or more: Sensor circuit shorted

    OK:
    Engine coolant temperature value displayed on the intelligent tester is almost the same as the engine coolant temperature receiver gauge indication.

  1. Record the temperature displayed on the intelligent tester.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature/Min.: -40°C (-40°F), Max.: 215°C (419°F)
    After warming up: 80 to 100°C (176 to 212°F)
    -

    OK:
    Engine coolant temperature value displayed on the intelligent tester is almost the same as the previously recorded intelligent tester indication (Body Electrical / Combination Meter / Data List / Coolant Temperature).

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2TR-FE)
    C
    NG (for 1KD-FTV)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temperature
    Engine coolant temperature/0 to 127.5°C (0 to 261.5°F)
    After warming up: 80 to 95°C (176 to 203°F)
    1. If -40°C (-40°F): Sensor circuit open
    2. If 140°C (284°F) or more: Sensor circuit shorted

    OK:
    Engine coolant temperature value displayed on the intelligent tester is almost the same as the engine coolant temperature receiver gauge indication.

  1. Record the temperature displayed on the intelligent tester.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


6. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Coolant Temp
    Engine coolant temperature/Min.: -40°C (-40°F), Max.: 215°C (419°F)
    After warming up: 80 to 100°C (176 to 212°F)
    -

    OK:
    Engine coolant temperature value displayed on the intelligent tester is almost the same as the previously recorded intelligent tester indication (Body Electrical / Combination Meter / Data List / Coolant Temperature).



NG
REPLACE ECM (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Engine Coolant Temperature Receiver Gauge Malfunction (Aug 2013 – Jul 2014)Odo/Trip Switch Malfunction (Aug 2013 – Jul 2014) →