2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0340 Camshaft Position Sensor Circuit

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed to the cylinder head. When the camshaft rotates, each of the 3 teeth on the camshaft passes by the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to determine the camshaft position. This signal is then used to control the ignition timing, fuel injection timing and VVT system.
DTC No.
DTC Detection Conditions
Trouble Areas
P0340
Either condition is met:
  1. Camshaft/crankshaft misalignment is detected at an engine speed of 600 rpm or more (1 trip detection logic).
  2. No VVT sensor signal is sent to the ECM during cranking (2 trip detection logic).
  1. Open or short in sensor circuit
  2. Camshaft position sensor
  3. Camshaft
  4. Timing chain has jumped tooth
  5. ECM

HINT:
DTC P0340 indicates a malfunction relating to the camshaft position sensor circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).

Reference: Inspection using an oscilloscope
A063955E36

HINT:
  1. The correct waveforms are as shown in the illustration.
  2. G2+ is the camshaft position sensor signal, and NE+ is the crankshaft position sensor signal.
  3. Grounding failure of the shielded wire may cause noise in the waveforms.
Item
Contents
ECM Terminal Name
CH1: G2 - NE-
CH2: NE+ - NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Cranking or idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the camshaft position sensor (Click here).



NG
REPLACE CAMSHAFT POSITION SENSOR (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C52-1 (G2) - C62-11 (G2)
    Always
    Below 1 Ω
    C52-2 (G-) - C62-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C52-1 (G2) or C62-11 (G2) - Body ground
    Always
    10 kΩ or higher
    C52-2 (G-) or C62-5 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the camshaft position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

  1. BR03795E25
    Check the camshaft position sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR (Click here)
OK


4. CHECK VALVE TIMING
  1. Check the valve timing.

    HINT:
    There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match-up the timing marks (Click here).



NG
ADJUST VALVE TIMING (Click here)
OK


5. INSPECT CAMSHAFT
  1. Check the teeth of the camshaft.

    OK:
    Camshaft teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT (Click here)
OK


6. REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0340 is output
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Aug 2013)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ P0352, P0353, P0354) (from Aug 2013) →