P0351 Ignition Coil "A" Primary / Secondary Circuit
Diagnostic trouble codes · Vehicles built from Aug 2013
Also covers:
- P0352 Ignition Coil "B" Primary / Secondary Circuit
- P0353 Ignition Coil "C" Primary / Secondary Circuit
- P0354 Ignition Coil "D" Primary / Secondary Circuit
DESCRIPTION
A Direct Ignition System (DIS) is used on this vehicle to enhance ignition accuracy and suppress high voltage losses.The DIS is an ignition system in which each cylinder is ignited by one ignition coil assembly. The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Based on the IGT signals, the ECM turns the power transistor inside the igniter on and off, turning the current to the primary coil on and off. When the current to the primary coil is cut off, a voltage is generated in the secondary coil and then applied to the spark plugs, causing them to spark inside the cylinders. At the same time, the igniter sends back the ignition confirmation (IGF) signal to the ECM.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0351 P0352 P0353 P0354 |
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- The following inspection procedure is for the No. 1 cylinder. If any of the other cylinders are malfunctioning, inspect their circuits by referring to the following procedure.
- If DTC P0351 is output, check the ignition coil assembly No. 1 circuit.
- If DTC P0352 is output, check the ignition coil assembly No. 2 circuit.
- If DTC P0353 is output, check the ignition coil assembly No. 3 circuit.
- If DTC P0354 is output, check the ignition coil assembly No. 4 circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The following inspection procedure is for the No. 1 cylinder. If any of the other cylinders are malfunctioning, inspect their circuits by referring to the following procedure.
| 1. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
DTC P0351, P0352, P0353 or P0354 is output
A
DTC P0351, P0352, P0353 and P0354 are output
B
|
|
||||
| A | |
| 2. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).
- NOTICE:
- Do not shuffle the connectors.
Perform a simulation test.
Check the DTCs output to the tester.
Result Result
Proceed to
Same DTC output
A
Different ignition coil assembly DTC output
B
|
|
||||
| A | |
| 3. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE) |
Disconnect the ignition coil assembly connectors.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C7-1 (+B) - C7-4 (GND)
Ignition switch ON
11 to 14 V
C8-1 (+B) - C8-4 (GND)
Ignition switch ON
11 to 14 V
C9-1 (+B) - C9-4 (GND)
Ignition switch ON
11 to 14 V
C10-1 (+B) - C10-4 (GND)
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Ignition Coil Assembly)
| Result |
Proceed to |
| OK |
A |
| NG (w/o Air Pressure Sensor) |
B |
| NG (w/ Air Pressure Sensor) |
C |
Reconnect the ignition coil assembly connectors.
|
|
||||
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C7-2 (IGF) - C64-10 (IGF1)
Always
Below 1 Ω
C8-2 (IGF) - C64-10 (IGF1)
Always
Below 1 Ω
C9-2 (IGF) - C64-10 (IGF1)
Always
Below 1 Ω
C10-2 (IGF) - C64-10 (IGF1)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C7-2 (IGF) or C64-10 (IGF1) - Body ground
Always
10 kΩ or higher
C8-2 (IGF) or C64-10 (IGF1) - Body ground
Always
10 kΩ or higher
C9-2 (IGF) or C64-10 (IGF1) - Body ground
Always
10 kΩ or higher
C10-2 (IGF) or C64-10 (IGF1) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the ignition coil assembly connectors.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C7-3 (IGT1) - C64-1 (IGT1)
Always
Below 1 Ω
C8-3 (IGT2) - C64-2 (IGT2)
Always
Below 1 Ω
C9-3 (IGT3) - C64-3 (IGT3)
Always
Below 1 Ω
C10-3 (IGT4) - C64-4 (IGT4)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C7-3 (IGT1) or C64-1 (IGT1) - Body ground
Always
10 kΩ or higher
C8-3 (IGT2) or C64-2 (IGT2) - Body ground
Always
10 kΩ or higher
C9-3 (IGT3) or C64-3 (IGT3) - Body ground
Always
10 kΩ or higher
C10-3 (IGT4) or C64-4 (IGT4) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the ignition coil assembly connectors.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) |
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C7-4 (GND) - Body ground
Always
Below 1 Ω
C8-4 (GND) - Body ground
Always
Below 1 Ω
C9-4 (GND) - Body ground
Always
Below 1 Ω
C10-4 (GND) - Body ground
Always
Below 1 Ω
| Result |
Proceed to |
| OK (w/o Air Pressure Sensor) |
A |
| OK (w/ Air Pressure Sensor) |
B |
| NG |
C |
Reconnect the ignition coil assembly connectors.
|
|
||||
|
|
||||
| A | |
| 7. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INTEGRATION RELAY [IG2 RELAY]) |
Disconnect the ignition coil assembly connectors.
Remove the integration relay (IG2 relay) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C7-1 (+B) - 1A-4
Always
Below 1 Ω
C8-1 (+B) - 1A-4
Always
Below 1 Ω
C9-1 (+B) - 1A-4
Always
Below 1 Ω
C10-1 (+B) - 1A-4
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C7-1 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
C8-1 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
C9-1 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
C10-1 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
Reinstall the integration relay.
Reconnect the ignition coil assembly connectors.
|
|
||||
| OK | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INJ NO. 2 RELAY) |
Disconnect the ignition coil assembly connectors.
Remove the INJ No. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C7-1 (+B) - INJ No. 2 relay terminal 3
Always
Below 1 Ω
C8-1 (+B) - INJ No. 2 relay terminal 3
Always
Below 1 Ω
C9-1 (+B) - INJ No. 2 relay terminal 3
Always
Below 1 Ω
C10-1 (+B) - INJ No. 2 relay terminal 3
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C7-1 (+B) or INJ No. 2 relay terminal 3 - Body ground
Always
10 kΩ or higher
C8-1 (+B) or INJ No. 2 relay terminal 3 - Body ground
Always
10 kΩ or higher
C9-1 (+B) or INJ No. 2 relay terminal 3 - Body ground
Always
10 kΩ or higher
C10-1 (+B) or INJ No. 2 relay terminal 3 - Body ground
Always
10 kΩ or higher
Reconnect the ignition coil assembly connectors.
Reinstall the INJ No. 2 relay.
|
|
||||
| OK | |
| 9. INSPECT INJ NO. 2 RELAY |
Inspect the INJ No. 2 relay (Click here).
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BATTERY) |
Remove the INJ No. 2 relay from the engine room relay block.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
INJ No. 2 relay terminal 5 - Positive battery terminal
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
INJ No. 2 relay terminal 5 or Positive battery terminal - Body ground
Always
10 kΩ or higher
Reinstall the INJ No. 2 relay.
Reconnect the cable to the positive (+) battery terminal.
Reconnect the cable to the negative (-) battery terminal.
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BODY GROUND) |
Remove the INJ No. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
INJ No. 2 relay terminal 2 - Body ground
Always
Below 1 Ω
Reinstall the INJ No. 2 relay.
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI RELAY] - INJ NO. 2 RELAY) |
Remove the INJ No. 2 relay from the engine room relay block.
Remove the integration relay (EFI relay) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
1B-4 - INJ No. 2 relay terminal 1
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
1B-4 or INJ No. 2 relay terminal 1 - Body ground
Always
10 kΩ or higher
Reinstall the integration relay.
Reinstall the INJ No. 2 relay.
|
|
||||
| OK | ||
| ||
