P0500 Vehicle Speed Sensor
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of this pulse signal.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0500 |
While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
- HINT:
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
- OK:
- Vehicle speeds displayed on tester and speedometer display are equal.
|
|
||||
| OK | ||
| ||
| 3. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE) |
![]() ![]() |
Disconnect the combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G6-32 (+S) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to combination meter assembly)
Reconnect the combination meter assembly connector.
|
|
||||
| OK | |
| 4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM) |
![]() ![]() |
Move the shift lever to N.
Jack up the vehicle.
Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G6-32 (+S) - Body ground
Ignition switch ON
Voltage generated intermittently
Text in Illustration *a
Component with harness connected
(combination meter assembly)
- HINT:
- The output voltage should fluctuate up and down, similarly to the diagram, when a wheel is turned slowly.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM) |
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G6-32 (+S) - G55-18 (SPD)
Always
Below 1 Ω
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
G6-32 (+S) or G55-18 (SPD) - Body ground
Always
10 kΩ or higher
Reconnect the combination meter assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||


