2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. BEARING POSITION

C212465E01

Bearing Diameter:
Mark
Front Race Diameter
Inside/Outside
Thrust Bearing Diameter
Inside/Outside
Rear Race Diameter
Inside/Outside
A
28.45 mm (1.12 in.)/29.9 to 30.1 mm (1.18 to 1.19 in.)
29.0 to 29.25 mm (1.14 to 1.15 in.)/50.04 to 50.34 mm (1.97 to 1.98 in.)
-
B
33.0 to 33.25 mm (1.30 to 1.31 in.)/49.9 to 50.4 mm (1.96 to 1.98 in.)
31.45 to 31.70 mm (1.24 to 1.25 in.)/49.1 to 49.4 mm (1.93 to 1.94 in.)
-
C
37.1 to 37.3 mm (1.46 to 1.47 in.)/58.70 to 58.95 mm (2.31 to 2.32 in.)
33.75 to 33.85 mm (1.329 to 1.333 in.)/49.8 to 50.3 mm (1.96 to 1.98 in.)
-
D
36.5 to 37 mm (1.44 to 1.46 in.)/50.75 to 50.95 mm (2.00 to 2.01 in.)
33.55 to 33.80 mm (1.32 to 1.33 in.)/47.62 to 47.87 mm (1.87 to 1.88 in.)
-
E
25.98 mm (1.02 in.)/48.87 mm (1.92 in.)
25.94 to 26.07 mm (1.02 to 1.03 in.)/46.62 to 46.87 mm (1.84 to 1.85 in.)
26.5 to 27.0 mm (1.04 to 1.06 in.)/47.02 mm (1.85 in.)
F
-
35 to 35.3 mm (1.38 to 1.39 in.)/50.50 to 53.75 mm (2.11 to 2.12 in.)
34 to 34.5 mm (1.34 to 1.36 in.)/48.5 to 49 mm (1.91 to 1.93 in.)
G
33.55 to 33.80 mm (1.32 to 1.33 in.)/47.3 to 47.8 mm (1.86 to 1.88 in.)
35.45 to 35.61 mm (1.396 to 1.402 in.)/47.62 to 47.87 mm (1.87 to 1.88 in.)
-
H
28.5 mm (1.12 in.)/44.2 mm (1.74 in.)
28.5 mm (1.12 in.)/44.2 mm (1.74 in.)
-
I
-
39.38 mm (1.55 in.)/57.94 to 58.36 mm (2.28 to 2.30 in.)
-


2. FIX TRANSMISSION CASE

AT05393E01
  1. Install the transmission case to an overhaul attachment.


3. INSTALL NO. 1 FIRST AND REVERSE BRAKE PISTON

AT08209E10
  1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

    Text in Illustration 
    *1
    No. 1 First and Reverse Brake Piston
    *2
    Reaction Sleeve

  1. Coat a new O-ring with ATF and install it to the reaction sleeve.

  1. Install the No. 1 brake piston to the reaction sleeve.

  1. D001243E04
    With the No. 1 brake piston underneath (the rear side), install the brake reaction sleeve and No. 1 brake piston to the transmission case.
    Text in Illustration 
    *1
    No. 1 First and Reverse Brake Piston
    *2
    Reaction Sleeve

    NOTICE:
    Be careful not to damage the O-rings.


4. INSTALL NO. 2 FIRST AND REVERSE BRAKE PISTON
  1. Coat a new O-ring with ATF and install it to the brake piston.

  1. AT08333E09
    With the spring seat of the piston facing upward (the front side), install the piston to the transmission case.
    Text in Illustration 
    *1
    No. 2 First and Reverse Brake Piston

    NOTICE:
    Be careful not to damage the O-ring.


5. INSTALL FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

AT05429E01
  1. Install the No. 2 brake return spring to the brake piston.

  1. AT08303E05
    Place SST on the brake return spring and compress the brake return spring.
    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring. Make sure the end gap of the snap ring is not aligned with a spring retainer claw.

    SST
    09350-30020   (09350-07070)
    Text in Illustration 
    *1
    Snap Ring
    *2
    Retainer Claw


6. INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE

AT05258E02
  1. Make sure the first and reverse brake pistons move smoothly when compressed air is applied to the transmission case.


7. INSTALL LEAF SPRING

AT05107E01

8. INSTALL REAR PLANETARY RING GEAR FLANGE

AT08206E01
  1. Install the ring gear flange to the rear planetary ring gear.

  1. Using a screwdriver, install the snap ring.

  1. C212475E01
    Coat the bearing and bearing race with petroleum jelly and install them to the rear planetary ring gear.

    Races and Bearing Diameter:
    Item
    Inside
    Outside
    Bearing H
    28.5 mm (1.12 in.)
    44.2 mm (1.74 in.)
    Bearing Race H
    28.5 mm (1.12 in.)
    44.2 mm (1.74 in.)

    Text in Illustration 
    *1
    Bearing H
    *2
    Bearing Race H

  1. D028060E01
    Coat the No. 2 planetary carrier thrust washer with petroleum jelly.

  1. Install the thrust washer to both sides of the planetary gear.

    HINT:
    Make sure that the tabs of the washer fit into the cutout portions of the planetary gear.


9. INSTALL NO. 2 1-WAY CLUTCH

C212488E01
  1. Install the 1-way clutch to the planetary gear.

    HINT:
    Make sure that the open ends of the guides of the 1-way clutch are facing upward.

    Text in Illustration 
    *1
    Open End
    *2
    Guide

  1. AT08192E01
    Using a screwdriver, install the snap ring.

  1. AT08191E01
    While turning the 1-way clutch inner race counterclockwise, install the 1-way clutch inner race to the planetary gear.


10. INSPECT NO. 2 1-WAY CLUTCH

AT08200E04
  1. Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


11. INSTALL REAR PLANETARY GEAR ASSEMBLY

D028061E01
  1. Coat the No. 1 planetary carrier thrust washer with petroleum jelly.

  1. Install the thrust washer to the planetary gear.

    HINT:
    Make sure that the tabs of the washer fit to the cutout portions of the planetary gear.

  1. AT08199E01
    Install the rear planetary gear to the rear planetary ring gear.


12. INSTALL PLANETARY OUTPUT SHAFT OIL SEAL RING

AT08198E01
  1. Coat the oil seal ring with ATF and install it to the output shaft.

    HINT:
    After installing the oil seal ring, check that it rotates smoothly.

    NOTICE:
    Do not expand the ring excessively.


13. INSTALL OUTPUT SHAFT

AT08197E01
  1. Install the output shaft to the rear planetary gear flange.


14. INSTALL SECOND BRAKE PISTON

AT08452E01
  1. Coat 2 new O-rings with ATF, and install them on the second brake piston.

  1. Being careful not to damage the O-rings, and press the second brake piston to the second brake drum with both hands.


15. INSTALL SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

AT08185E04
  1. Install the piston return spring.

  1. Install the second brake piston return spring seat.

  1. AT08438E01
    Place SST on the spring retainer and compress the return spring with a press.
    SST
    09350-30020   (09350-07040)

    CAUTION:
    Do not deform the spring sheet. Stop compressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Do not expand the snap ring excessively.


16. INSPECT SECOND BRAKE PISTON

AT08439E01
  1. Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.


17. INSTALL NO. 4 PLANETARY CARRIER THRUST WASHER

AT08184E01
  1. Coat the thrust washer with petroleum jelly and install it.

    HINT:
    Make sure that the cutout portions of the thrust washer fit onto the teeth of the spring retainer.


18. INSTALL FIRST AND REVERSE BRAKE DISC SET

C212477E01
  1. Install the flange with the rounded edge facing upward.

  1. Install the 6 discs and 6 plates.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3

    Text in Illustration 
    *1
    Flange
    *2
    Disc
    *3
    Plate


19. INSTALL OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM

C212487
  1. Coat the bearing with petroleum jelly and install it to the case.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing I
    39.38 mm (1.55 in.)
    57.94 to 58.36 mm (2.28 to 2.30 in.)

    NOTICE:
    Make sure the bearing is installed facing the proper direction.

  1. AT07893E01
    Align the teeth on the flange, discs and plates.

  1. Q004066E01
    Install the 2nd brake drum to the planetary gear with the snap ring facing upward.

    NOTICE:
    Make sure the oil hole in the drum faces towards the lower side of the transmission case (the side where the valve body is installed).

  1. Q004068E04
    Align the teeth of the planetary gear assembly, indicted by A in the illustration, with the splines of the transmission case, indicated by B in the illustration.

  1. AT05158E01
    Install the assembled planetary gear.

  1. Z005131E04
    Place the output shaft on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block

  1. AT05396E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


20. SELECT FIRST AND REVERSE BRAKE FLANGE

AT08223E01
  1. Using a feeler gauge, measure the clearance between the plate and second brake drum.

    Standard clearance:
    0.70 to 1.22 mm (0.0276 to 0.0480 in.)

    If the clearance is not as specified, select another flange.
    If the clearance is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    55
    3.94 to 4.06 mm (0.155 to 0.160 in.)
    54
    4.14 to 4.26 mm (0.163 to 0.168 in.)
    53
    4.34 to 4.46 mm (0.171 to 0.176 in.)
    52
    4.54 to 4.66 mm (0.179 to 0.183 in.)
    51
    4.74 to 4.86 mm (0.187 to 0.191 in.)
    50
    4.92 to 5.08 mm (0.194 to 0.200 in.)
    66
    5.10 to 5.30 mm (0.201 to 0.209 in.)
    67
    5.30 to 5.50 mm (0.209 to 0.217 in.)


21. INSTALL SECOND BRAKE PISTON SLEEVE

AT05397E01

22. INSTALL BRAKE DRUM GASKET

AT04469E01
  1. Coat a new gasket with ATF and install it.


23. INSTALL NO. 1 1-WAY CLUTCH ASSEMBLY

AT05231E01
  1. Install the thrust washer to the second brake piston return spring.

  1. Z005133E03
    Install the 1-way clutch as shown in the illustration.


24. INSTALL SECOND BRAKE DISC SET

AT05398E10
  1. Install the 1.8 mm (0.0709 in.) thick plate with the rounded edge of the plate facing the discs.

  1. Install the 5 discs, 4 2.5 mm (0.0984 in.) thick plates and flange.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *4

    Text in Illustration 
    *1
    1.8 mm (0.0709 in.) Thick Plate
    *2
    Disc
    *3
    2.5 mm (0.0984 in.) Thick Plate
    *4
    Flange

  1. AT05476E01
    Using a screwdriver, install the snap ring.


25. INSPECT SECOND BRAKE

AT05215E01
  1. Using a feeler gauge, measure the clearance between the snap ring and flange.

    Standard clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is not as specified, inspect the discs.


26. INSTALL SUN GEAR INPUT DRUM SHAFT SNAP RING

AT08182E01
  1. Using a screwdriver, install the snap ring to the planetary sun gear.


27. INSTALL SUN GEAR INPUT DRUM

AT08181E01
  1. Place the planetary sun gear onto a wooden block or similar object.

  1. Install the input drum to the planetary sun gear.

  1. AT07897E01
    Using snap ring pliers, install the snap ring.


28. INSTALL SUN GEAR SHAFT OIL SEAL RING

AT08189E01
  1. Coat the 2 oil seal rings with ATF.

  1. Install the 2 oil seal rings to the planetary sun gear.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.

    NOTICE:
    Do not expand the ring excessively.


29. INSTALL NO. 1 1-WAY CLUTCH THRUST WASHER

AT01642E01

HINT:
Make sure that the tabs of the washer fit into the holes in the sun gear input drum.


30. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM

Q000840E01
  1. While turning the sun gear clockwise, install it to the 1-way clutch.

    HINT:
    Confirm that the thrust washer is installed correctly.


31. INSTALL FRONT PLANETARY GEAR ASSEMBLY

D029745E04
  1. Coat the bearing and bearing race with petroleum jelly and install them to the planetary gear.

    Bearing and Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race G
    33.55 to 33.80 mm (1.32 to 1.33 in.)
    47.3 to 47.8 mm (1.86 to 1.88 in.)
    Bearing G
    35.45 to 35.61 mm (1.396 to 1.402 in.)
    47.62 to 47.87 mm (1.87 to 1.88 in.)

    Text in Illustration 
    *1
    Bearing Race G
    *2
    Bearing G

    NOTICE:
    Make sure the bearing and race are installed facing the proper directions.

  1. D029741E01
    Install the planetary gear to the sun gear input drum.

  1. D029740E03
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07070)

  1. Remove the wooden blocks from under the output shaft.

  1. C220045
    Coat the bearing race with petroleum jelly and install it to the planetary gear.

    Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race F
    34 to 34.5 mm (1.34 to 1.36 in.)
    48.5 to 49 mm (1.91 to 1.93 in.)

    NOTICE:
    Be careful to the installation direction of the bearing race.


32. INSTALL SECOND COAST BRAKE BAND ASSEMBLY

Q004030E01
  1. Install the brake band to the case.

  1. Q000788E01
    Install the pin to the brake band as shown in the illustration.

  1. Install the E-ring to the pin.


33. INSTALL INPUT SHAFT OIL SEAL RING

D025664E01
  1. Coat the 3 oil seal rings with ATF.

  1. Squeeze the ends of the 3 oil seal rings together, and then install them to the forward clutch drum groove.

    NOTICE:
    Do not expand the rings excessively.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.


34. INSTALL FRONT CLUTCH PISTON SUB-ASSEMBLY

D001365E04
  1. Coat 2 new O-rings with ATF and install them to the forward clutch piston.

    Text in Illustration 
    *1
    O-Ring

  1. Coat a new O-ring with ATF and install it to the forward clutch drum.

  1. D001366E01
    Press the clutch piston into the forward clutch drum with both hands to install it.

    NOTICE:
    Be careful not to damage the O-ring.


35. INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

D025660E04
  1. Install the piston return spring.

  1. D025659E03
    Place SST on the spring retainer, compress the return spring with a press, and then install the snap ring.
    SST
    09350-30020   (09350-07040, 09350-07070)

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


36. INSTALL FORWARD CLUTCH DISC SET

AT08177E01
  1. Install the cushion plate.

  1. G037485E02
    Install the 6 plates, 6 discs and flange.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange

  1. AT08174E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the cutout portion of the forward clutch drum.


37. SELECT FORWARD CLUTCH FLANGE

AT07843E04
  1. Using SST and a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))

    SST
    09350-30020   (09350-06120)

    Standard moving distance (A):
    0.60 to 1.00 mm (0.0236 to 0.0394 in.)

    If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    90
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    91
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    92
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    93
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    94
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    95
    3.95 to 4.05 mm (0.156 to 0.159 in.)
    96
    4.15 to 4.25 mm (0.163 to 0.167 in.)
    97
    4.35 to 4.45 mm (0.171 to 0.175 in.)


38. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

D001453E04
  1. Coat 2 new O-rings with ATF and install them to the direct clutch piston.

    Text in Illustration 
    *1
    O-Ring

  1. D001354E01
    Press the clutch piston into the clutch drum with both hands to install it.

    NOTICE:
    Be careful not to damage the O-rings.


39. INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

D001349E05

  1. D001348E04
    Place SST on the spring retainer and compress the return spring with a press.
    SST
    09350-30020   (09350-07040)

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


40. INSTALL DIRECT CLUTCH DISC SET

C212472E01
  1. Install the 3 plates and 3 discs.

  1. Install the flange with the flat end facing downward.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange

  1. G037155E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the cutout portion of the direct clutch drum.


41. SELECT DIRECT CLUTCH FLANGE

AT08250E01
  1. Place the direct clutch to the overdrive support.

  1. G037156E03
    Using SST and a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (186 to 206 kPa (1.9 to 2.1 kgf/cm2, 27 to 30 psi)).
    SST
    09350-30020   (09350-06120)

    Standard moving distance (A):
    0.40 to 0.70 mm (0.0157 to 0.0276 in.)

    If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    53
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    54
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    55
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    56
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    57
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    58
    3.75 to 3.85 mm (0.148 to 0.152 in.)


42. INSTALL DIRECT CLUTCH ASSEMBLY

D006214E06
  1. Install the bearing and thrust washer to the forward clutch.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing D
    33.55 to 33.80 mm (1.32 to 1.33 in.)
    47.62 to 47.87 mm (1.87 to 1.88 in.)

    Text in Illustration 
    *1
    Bearing D
    *2
    Thrust Washer

  1. AT05262E03
    Install the direct clutch to the forward clutch.


43. INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

Z005137E03
  1. Coat the bearing race and bearing with petroleum jelly and install them to the forward clutch.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing Race E
    25.98 mm (1.02 in.)
    48.87 mm (1.92 in.)
    Bearing E
    25.94 to 26.07 mm (1.02 to 1.03 in.)
    46.62 to 46.87 mm (1.84 to 1.85 in.)

    Text in Illustration 
    *1
    Bearing Race E
    *2
    Bearing E

    NOTICE:
    Make sure the bearing and race are installed facing the proper directions.

  1. Z005136E04
    Coat the bearing race with petroleum jelly and install it to the front planetary ring gear.

    Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race E
    26.5 to 27.0 mm (1.04 to 1.06 in.)
    47.02 mm (1.85 in.)

    NOTICE:
    Make sure the bearing race is installed facing the proper directions.

  1. AT05432E01
    Align the teeth of the discs in the forward clutch.

  1. Q000838E04
    Align the splines of the planetary ring gear with the teeth of the discs and install the planetary ring gear to the forward clutch.


44. INSTALL DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY

AT08306E03
  1. Coat the bearing with petroleum jelly and install it to the ring gear.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing F
    35 to 35.3 mm (1.38 to 1.39 in.)
    50.50 to 53.75 mm (2.11 to 2.12 in.)

    Text in Illustration 
    *1
    Bearing F

    NOTICE:
    Make sure the bearing is installed facing the proper directions.

  1. AT08234E01
    Install the assembled direct clutch, forward clutch and front planetary ring gear to the transmission case.

  1. AT05213E01
    Using a vernier caliper, measure the distance between the sun gear input drum and direct clutch drum as shown in the illustration.

    Standard distance:
    5.3 to 7.3 mm (0.209 to 0.287 in.)

    If the distance is not as specified, check for improper installation.

  1. Z005236E03
    Coat the bearing with petroleum jelly and install it to the forward clutch.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing D
    33.55 to 33.80 mm (1.32 to 1.33 in.)
    47.62 to 47.87 mm (1.87 to 1.88 in.)

    NOTICE:
    Make sure the bearing is installed facing the proper directions.


45. INSTALL SECOND COAST BRAKE PISTON ROD

  1. D001299E05
    Install the washer plate, compression spring and piston to the piston rod.
    *1
    Piston Rod
    *2
    Washer Plate
    *3
    Compression Spring
    *4
    Piston

  1. AT05260E01
    Firmly press the piston down to compress the compression spring.

  1. Install the E-ring.


46. INSTALL SECOND COAST BRAKE PISTON OIL SEAL RING

G037154E01
  1. Coat a new oil seal ring with ATF.

  1. Spread the ends of the ring to install the oil seal ring to the piston groove. Then squeeze its ends together.

    NOTICE:
    Do not spread the ring ends excessively.


47. INSTALL SECOND COAST BRAKE PISTON ASSEMBLY

AT05086E01
  1. Coat 2 new O-rings with ATF and install them to the second coast brake cover.

  1. Install the spring, piston assembly and cover to the case.

  1. AT05127E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


48. INSPECT PISTON STROKE OF SECOND COAST BRAKE

AT05216E04
  1. Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.

    Text in Illustration 
    *1
    Piston Rod
    *2
    Mark

  1. AT05217E02
    Using SST, measure the piston stroke while applying and releasing a compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.0591 to 0.118 in.)

    If the piston stroke is not as specified, inspect the brake band.
    If the piston stroke is not as specified, select a piston rod of an appropriate length from the table below so that the measured value is within the standard range.

    Piston Rod Length:
    Groove Mark
    Length
    Without
    78.3 to 78.5 mm (3.08 to 3.09 in.)
    With
    79.8 to 80.0 mm (3.14 to 3.15 in.)


49. INSTALL OVERDRIVE CLUTCH DRUM OIL SEAL RING

AT08151E01
  1. Coat 2 new oil seal rings with ATF.

  1. Squeeze the ends of the 2 oil seal rings together, and then install them to the stator shaft groove.

    NOTICE:
    Do not expand the rings excessively.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.

  1. AT08158E01
    Coat the thrust washer with petroleum jelly and install it to the overdrive support.

    HINT:
    Make sure that the tab of the washer fits into the groove of the overdrive support.


50. INSTALL OVERDRIVE BRAKE PISTON

D001336E04
  1. Coat 2 new O-rings with ATF and install them to the overdrive brake piston.

    Text in Illustration 
    *1
    O-Ring

  1. AT01979E01
    Press the brake piston into the overdrive support with both hands to install it.

    NOTICE:
    Be careful not to damage the O-rings.


51. INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

AT01978E01
  1. Install the return spring to the brake piston.

  1. D001341E01
    Place SST on the spring retainer and compress the return spring with a press.
    SST
    09350-30020   (09350-07030)

  1. Using a screwdriver, install the snap ring.

    NOTICE:
    D025625E02
    Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive support.

    HINT:
    1. After assembling the overdrive support assembly completely, align the position of the piston with A in the illustration.
    2. Align the end gap of the snap ring with B in the illustration.
    3. Make sure that the snap ring is not on the part of return spring that prevents the spring from coming off. Check this for the 8 places.


52. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE

AT08451E01
  1. Place the overdrive support assembly to the direct clutch assembly.

  1. AT08149E01
    Apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.


53. INSTALL OVERDRIVE BRAKE ASSEMBLY

AT05110E07
  1. Coat the bearing and bearing race with petroleum jelly and install them to the overdrive brake assembly.

    Bearing and Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing C
    33.75 to 33.85 mm (1.329 to 1.333 in.)
    49.8 to 50.3 mm (1.96 to 1.98 in.)
    Bearing Race D
    36.5 to 37 mm (1.44 to 1.46 in.)
    50.75 to 50.95 mm (2.00 to 2.01 in.)

    Text in Illustration 
    *1
    Bearing C
    *2
    Bearing Race D

    NOTICE:
    Make sure the bearing and race are installed facing the proper directions.

  1. AT05159E01
    Confirm that the thrust washer is installed correctly.

    HINT:
    Make sure that the tab of the washer fits into the hole on the overdrive brake assembly.

  1. AT05400E04
    Using the 2 bolts of SST, aim the bolt and oil holes of the overdrive brake assembly toward the valve body side, and align them with the bolt holes of the transmission case. Then install the overdrive brake assembly.
    SST
    09350-30020   (09350-07020)

  1. Temporarily install the 2 bolts.

  1. Q000618E06
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)

    Standard distance A:
    24 mm (0.945 in.)

    HINT:
    Install the snap ring with the open end facing toward the valve body.

  1. AT05218E01
    Tighten the 2 bolts.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }


54. INSPECT OUTPUT SHAFT END PLAY

Z006796E01
  1. Using a dial indicator, measure the end play of the output shaft while moving it by hand.

    Standard end play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the end play is not as specified, check for improper installation.

  1. Check that the output shaft rotates smoothly.


55. INSTALL OVERDRIVE BRAKE DISC SET

C213738E01
  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *2
    Flange

  1. AT05233E01
    Using a screwdriver, install the snap ring.


56. SELECT OVERDRIVE BRAKE FLANGE

AT05282E03
  1. Place SST and a dial indicator on the overdrive brake piston.

    SST
    09350-30020   (09350-06120)

  1. Measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))

    Standard piston stroke:
    1.75 to 2.05 mm (0.0689 to 0.0807 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
    If the piston stroke is still outside the standard, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    33
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    35
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    36
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    37
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    38
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    39
    3.85 to 3.95 mm (0.152 to 0.156 in.)
    40
    3.95 to 4.05 mm (0.156 to 0.159 in.)


57. INSTALL OVERDRIVE PLANETARY RING GEAR FLANGE

AT08134E01
  1. Install the ring gear flange to the overdrive planetary ring gear.

  1. AT08133E01
    Using a screwdriver, install the snap ring.


58. INSTALL OVERDRIVE PLANETARY RING GEAR

Q000842E03
  1. Coat the bearing race with petroleum jelly and install it to the overdrive planetary ring gear flange.

    Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race C
    37.1 to 37.3 mm (1.46 to 1.47 in.)
    58.70 to 58.95 mm (2.31 to 2.32 in.)

    Text in Illustration 
    *1
    Bearing Race C

    NOTICE:
    Make sure the bearing race is installed facing the proper directions.

  1. AT05146E01
    Install the ring gear.


59. INSTALL NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER

C212485
  1. Install the thrust washer to the overdrive planetary gear with the grooves facing upward.


60. INSTALL OVERDRIVE 1-WAY CLUTCH

C212484E01
  1. Install the 2 retainers to the 1-way clutch.

  1. Install the 1-way clutch to the outer race with the flange of the 1-way clutch facing upward.

    Text in Illustration 
    *1
    Flange

  1. AT01638E05
    Install the overdrive 1-way clutch and outer race to the overdrive planetary gear.


61. INSTALL OVERDRIVE RETAINING PLATE

AT08146E01
  1. Install the retaining plate.

  1. AT08135E01
    Using a screwdriver, install the snap ring.


62. INSPECT OVERDRIVE 1-WAY CLUTCH

AT08138E04
  1. Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


63. INSTALL OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT08144E01
  1. Coat 2 new O-rings with ATF, and install them to the overdrive direct clutch piston.

  1. Press the clutch piston into the clutch drum with both hands to install it.

    NOTICE:
    Be careful not to damage the O-rings.


64. INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

AT08145E01
  1. Install the overdrive brake return spring on the overdrive direct clutch piston.

  1. Z004660E04
    Place SST on the spring retainer and compress the return spring with a press.
    SST
    09350-30020   (09350-07040)

  1. Using a screwdriver, install the snap ring.

    Text in Illustration 
    *1
    Retainer Claw

    NOTICE:
    1. Do not deform the spring sheet. Stop compressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.
    2. Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


65. INSTALL OVERDRIVE DIRECT CLUTCH DISC SET

AT01639E03
  1. Install the 2 plates and 2 discs.

    Install in order:
    *1 - *2 - *1 - *2

    Text in Illustration 
    *1
    Plate
    *2
    Disc

  1. AT08155E01
    Install the flange with the flat end facing downward.

  1. AT08131E01
    Using a screwdriver, install the snap ring.


66. SELECT OVERDRIVE CLUTCH FLANGE

AT08140E01
  1. Place the oil pump onto the torque converter clutch, and then place the overdrive direct clutch drum assembly to the oil pump.

  1. AT04448E05
    Using SST and a dial indicator, measure the overdrive direct clutch piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09350-30020   (09350-06120)

    Standard piston stroke:
    1.85 to 2.15 mm (0.0728 to 0.0846 in.)

    Text in Illustration 
    *1
    Vinyl Tape
    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
    If the piston stroke is still not as specified, select another flange.
    If the piston stroke is still outside the standard, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    21
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    20
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    19
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    18
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    17
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    16
    3.55 to 3.65 mm (0.140 to 0.144 in.)


67. INSTALL OVERDRIVE DIRECT CLUTCH DRUM

AT08130E01
  1. Align the teeth of the discs in the direct clutch assembly.

  1. Install the direct clutch drum assembly to the overdrive planetary gear.


68. INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY WITH DIRECT CLUTCH ASSEMBLY AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY

  1. G035543E06
    Coat the bearing with petroleum jelly and install it to the ring gear.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing B
    31.45 to 31.70 mm (1.24 to 1.25 in.)
    49.1 to 49.4 mm (1.93 to 1.94 in.)

    Text in Illustration 
    *1
    Bearing B

    NOTICE:
    Make sure the bearing is installed facing the proper directions.

  1. Z005128E02
    Coat the bearing race with petroleum jelly and install it to the planetary gear.

    Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race B
    33.0 to 33.25 mm (1.30 to 1.31 in.)
    49.9 to 50.4 mm (1.96 to 1.98 in.)

    Text in Illustration 
    *1
    Bearing Race B

    NOTICE:
    Make sure the bearing race is installed facing the proper directions.

  1. Q000619E01
    Install the overdrive planetary gear with overdrive direct clutch and 1-way clutch.

  1. AT04470E03
    Place SST on the transmission case.
    SST
    09350-36010   (09350-06090)

  1. Using a vernier caliper, measure the distance between the top of SST and clutch drum.

    Standard distance:
    15.5 to 16.5 mm (0.610 to 0.650 in.)

    If the distance is not as specified, check for improper installation.

  1. AT08313E03
    Coat the bearing with petroleum jelly and install it to the overdrive direct clutch.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing A
    29.0 to 29.25 mm (1.14 to 1.15 in.)
    50.04 to 50.34 mm (1.97 to 1.98 in.)

    Text in Illustration 
    *1
    Bearing A

    NOTICE:
    Make sure the bearing is installed facing the proper directions.


69. INSTALL OIL PUMP ASSEMBLY

Z005237E03
  1. Coat the bearing race with petroleum jelly and install it to the oil pump.

    Bearing Race Diameter:
    Item
    Inside
    Outside
    Bearing Race A
    28.45 mm (1.12 in.)
    29.9 to 30.1 mm (1.18 to 1.19 in.)

    Text in Illustration 
    *1
    Bearing Race A

    NOTICE:
    Make sure the bearing race is installed facing the proper directions.

  1. Coat a new O-ring with ATF, and install it to the pump body.

  1. Slide the oil pump onto the input shaft, align the bolt holes of the oil pump assembly with the bolt holes of the transmission case and install the oil pump.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings to the overdrive direct clutch drum.

    NOTICE:
    Do not forcefully push on the oil pump as the oil seal rings will stick to the direct clutch drum.

  1. AT05404E01
    Install the 7 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }


70. INSPECT INPUT SHAFT ROTATION

AT05244E01
  1. Make sure the input shaft rotates smoothly.


71. INSPECT INDIVIDUAL PISTON OPERATION

AT05275E09
  1. Check the operating sound while applying compressed air to the oil hole indicated in the illustration.

    Text in Illustration 
    *1
    Overdrive Direct Clutch (C1)
    *2
    Direct Clutch (C2)
    *3
    Forward Clutch (C3)
    *4
    Overdrive Brake (B1)
    *5
    Second Coast Brake (B2)
    *6
    Second Brake (B3)
    *7
    First and Reverse Brake (B4)
    *8
    C-0 Accumulator Piston Hole

    HINT:
    When inspecting the overdrive direct clutch, check the operation sound with the C-0 accumulator piston hole closed.
    If there is no sound, disassemble and check the parts installation condition.


72. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

AT05238E03
  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)

  1. Coat the lips of the oil seals with MP grease.


73. INSTALL MANUAL VALVE LEVER SHAFT

Q000775E03
  1. Install a new spacer to the manual valve lever.

    Text in Illustration 
    *1
    Spacer
    *2
    Manual Valve Lever Shaft
    *3
    Manual Valve Lever

  1. Pass the manual valve lever shaft through the transmission case and the manual valve lever to install it.

  1. AT05405E01
    Using a hammer, tap in a new spring pin.

  1. D006523E01
    Align the manual valve lever indentation with the spacer hole, and stake them with the punch.

  1. Check that the shaft rotates smoothly.


74. INSTALL PARKING LOCK PAWL

Z006720E05
  1. Install the E-ring to the parking lock pawl shaft.

    Text in Illustration 
    *1
    E-Ring
    *2
    Parking Lock Pawl Shaft
    *3
    Parking Lock Pawl
    *4
    Spring

  1. Install the parking lock pawl, shaft and spring.


75. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

Z006797E01
  1. Connect the parking lock rod to the manual valve lever to install it.


76. INSTALL PARKING LOCK PAWL BRACKET

AT05406E01
  1. Install the parking lock pawl bracket to the transmission case and with the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Z005222E04
    Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked by the parking lock pawl.
    Text in Illustration 
    *1
    Manual Valve Lever
    *2
    Planetary Ring Gear
    *3
    Parking Lock Pawl


77. INSTALL C-0 ACCUMULATOR PISTON
  1. Coat a new O-ring with ATF and install it to the piston.

  1. AT05010E05
    Install the 2 springs and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Item
    Free Length
    Outer Diameter
    Color
    C-0 Inner Spring
    46.0 mm (1.81 in.)
    14.02 mm (0.552 in.)
    Yellow
    C-0 Outer Spring
    74.6 mm (2.94 in.)
    20.9 mm (0.823 in.)
    Orange


78. INSTALL B-0 ACCUMULATOR PISTON

AT05010E06
  1. Coat 2 new O-rings with ATF and install them to the piston.

  1. Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Item
    Free Length
    Outer Diameter
    Color
    B-0 Spring
    63.6 mm (2.50 in.)
    16.0 mm (0.630 in.)
    Red


79. INSTALL C-2 ACCUMULATOR PISTON

AT05010E07
  1. Coat 2 new O-rings with ATF and install them to the piston.

  1. Install the 2 springs and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Item
    Free Length
    Outer Diameter
    Color
    C-2 Inner Spring
    42.06 mm (1.66 in.)
    14.7 mm (0.579 in.)
    Pink
    C-2 Outer Spring
    68.53 mm (2.70 in.)
    20.2 mm (0.795 in.)
    Blue


80. INSTALL B-2 ACCUMULATOR PISTON

AT05010E08
  1. Coat 2 new O-rings with ATF and install them to the piston.

  1. Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Item
    Free Length
    Outer Diameter
    Color
    B-2 Spring
    70.50 mm (2.78 in.)
    19.9 mm (0.783 in.)
    Light Green


81. INSTALL CHECK BALL BODY

AT05098E03
  1. Install the spring and check ball body.

    Text in Illustration 
    *1
    Spring
    *2
    Check Ball Body


82. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

AT08393E06
  1. Install the valve body and align the groove of the manual valve with the pin of the manual valve lever.

    Text in Illustration 
    *1
    Manual Valve
    *2
    Pin
    *3
    Manual Valve Lever

  1. D029011E08
    Install the 20 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    23 mm (0.906 in.) for A
    28 mm (1.10 in.) for B
    36 mm (1.42 in.) for C


83. INSTALL TRANSMISSION WIRE

AT05066E02
  1. Coat a new O-ring with ATF and install it to the transmission wire.

  1. Install the transmission wire to the case, and then install the stopper plate with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C212457E02
    Connect the 4 connectors to the 4 shift solenoid valves.
    Text in Illustration 
    *1
    White
    *2
    Black
    *3
    Orange/Green
    *4
    Yellow/Brown

  1. Connect the temperature sensor with temperature sensor clamp and the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 ft.*lbf }


84. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

D005554E02
  1. Install 3 new gaskets to the oil strainer.

  1. D028706E04
    Install the oil strainer with the 4 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    14 mm (0.55 in.) for A
    20 mm (0.79 in.) for B
    23 mm (0.91 in.) for C


85. INSTALL OIL CLEANER MAGNET

C213709
  1. Install the 3 magnets.


86. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

AT01362E07
  1. Remove all old seal packing from the contact surfaces of the transmission case and oil pan.

    NOTICE:
    Be careful not to drop oil on the contact surfaces of the transmission case and oil pan.

  1. Apply seal packing to the oil pan.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent
    Seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

  1. C212456
    Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


87. INSTALL SENSOR ROTOR

C212455
  1. Install the key on the output shaft.

  1. Align the groove of the sensor rotor with the key and install the sensor rotor.

  1. C212454
    Using snap ring pliers, install the snap ring.


88. INSTALL TRANSFER CASE REAR ADAPTER OIL RECEIVER

C212453
  1. Install the transfer case rear adaptor oil receiver to the rear transfer adaptor.

  1. Using snap ring expander, install the snap ring.


89. INSTALL TRANSFER CASE ADAPTER REAR OIL SEAL
  1. Coat the lip of a new oil seal with ATF.

  1. C214906E01
    Using SST and a hammer, tap in the oil seal.
    SST
    09950-60010   (09951-00560)
    09950-70010   (09951-07150)

    Standard depth:
    0 to 1 mm (0 to 0.394 in.)


90. INSTALL REAR TRANSFER ADAPTER
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. C173937E03
    Apply seal packing to the rear adaptor transfer.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

    Seal diameter:
    1.0 to 1.5 mm (0.0394 to 0.0591 in.)

    Text in Illustration 
    *1
    Seal Packing

  1. C212451E01
    Install the rear adaptor transfer with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    50 mm (1.97 in.) for A
    40 mm (1.58 in.) for B


91. INSTALL AUTOMATIC TRANSMISSION HOUSING

C212450E01
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Apply adhesive to the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324,
    Three Bond 1324 or equivalent

  1. Install the transmission housing with the 6 bolts.

    Torque:
    for 14 mm bolt A:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for 17 mm bolt B:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }


92. INSTALL SPEED SENSOR SP2

G035550E01
  1. Install a new O-ring to the sensor.

  1. Install the sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


93. INSTALL SPEED SENSOR NC0

Q003894E01
  1. Install a new O-ring to the sensor.

  1. Install the speed sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


94. INSTALL OIL COOLER TUBE UNION

G034863E01
  1. Coat 2 new O-rings with ATF and install one to each tube union.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


95. INSTALL AUTOMATIC TRANSMISSION FLUID TEMPERATURE SENSOR

G034862E01
  1. Coat a new O-ring with ATF and install it to the sensor.

  1. Install the sensor.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


96. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

G037204E01
  1. Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and the nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. D028682E04
    Turn the control shaft lever LH clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. D006517E03
    Align the neutral basic line with the switch groove, as shown in the illustration, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    Text in Illustration 
    *1
    Neutral Basic Line
    *2
    Groove

  1. Using a screwdriver, bend the tabs of the lock washer.


97. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

D028070E02
  1. Install the control shaft lever with the washer and nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


98. INSTALL BREATHER HOSE

C213735E01

99. INSTALL DRAIN PLUG
  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

← INSPECTION (from Aug 2013)INSPECTION (from Aug 2013) →